Document Outline

• 9103-1390 534B SERVICE MANUAL
  • OPERATOR INSTRUCTION & LUBRICATION
    • 48729 Operation & Lubrication Manual
      • IMPORTANT SAFETY NOTICE
      • INTRODUCTION
        • General
        • Operator Qualifications
        • Related Manuals and Decals
        • Serial Number Location
        • Orientation
      • NOMENCLATURE
      • SAFETY HIGHLIGHTS
      • DECALS
      • HAND SIGNALS
      • OPERATOR'S CAB
      • CONTROL AND INSTRUMENT IDENTIFICATION
      • CHECKS AND SERVICES BEFORE STARTING ENGINE
      • ENGINE OPERATION
        • Starting Engine
        • Cold Weather Starting Aids
        • Normal Engine Operation
        • Stopping the Engine
      • WARM UP AND OPERATIONAL CHECKS
      • BRAKE SYSTEM
        • General
        • Inching
        • Service Brakes
        • Parking Brakes
      • STEERING SYSTEM
      • DRIVE TRAIN
        • General
        • Two and Four Wheel Drive
        • Transmission
        • Torque Converter
        • Front Driving Axle
        • Rear Driving Axle
        • Inching Travel
        • Moving Handler with Dead Engine
      • MATERIAL HANDLING
        • Leveling
        • Boom
        • Attachments
        • Attachments Capacities
        • Attachment Installation
      • OPERATING PROCEDURES AND TECHNIQUES
        • Hydraulic Controls
        • Rated Capacity Chart
      • PARKING
      • STORAGE
      • RECOMMENDED LUBRICANTS AND CAPACITIES
      • TIRE SPECIFICATIONS
      • LUBRICATION AND MAINTENANCE DIAGRAM
      • LUBRICATION FREQUENCIES
    • 28327 Preventive Maintenance Chart
  • HYDRAULIC SYSTEM
    • 48730 System Operation Manual
      • NOMENCLATURE
      • CONTROL & INSTRUMENT IDENTIFICATION
      • ENGINE
      • ELECTRICAL & FUEL TANK
      • MAIN FRAME, FRONT DRIVE AXLE, DRIVE SHAFT
      • REAR DRIVE & STEERING AXLE
      • HYDRAULIC MOTORS AND TIRES
      • TRANSMISSION & TORQUE CONVERTER
      • STEERING CIRCUIT
      • BRAKE CIRCUIT NOMENCLATURE
      • HYDRAULIC SERVICE BRAKES, WET DISC BRAKES
      • SERVICE & PARKING BRAKE APPLICATIONS
      • HYDRAULIC SYSTEM NOMENCLATURE
      • HYDRAULIC CYLINDERS
      • MAIN PUMP CIRCUITS
      • PILOT PUMP CIRCUIT
      • HYDRAULIC CIRCUITS, SWAY CIRCUIT
      • AUXILIARY HYDRAULIC SYSTEM
      • TILT & COMPENSATING CIRCUITS
      • CROWD CIRCUIT & MOVEMENTS
      • BOOM SECTIONS & SLIDER PADS
      • LIFT CIRCUIT, MANUAL "QUICK SWITCH" ASS'Y
      • OUTRIGGER CIRCUITS (OPTIONAL)
      • FRONT & REAR WHEEL DRIVE
      • FORWARD/REVERSE LEVER (Neutral & Shifted)
      • INCHING
      • QUICK SWITCH ATTACHMENTS
    • 81-515-009 Mico Sliding Caliper Disc Brakes Service Manual
      • General Installation
      • Adjustment, Change Ball & Cam, and Change Lining Procedures
      • Illustration
    • 81-600-001 Mico Guideline for Installing Hydraulic Brake Components
    • 81-950-016 Mico Brake Service Procedure
    • 81-460-159 Mico Hydraulic Brake Valve
  • TESTING & ADJUSTING
    • 48731 Testing & Adjusting Manual
      • Introduction - Pumps
      • Tools Needed to Test System
      • How to Test Pump Flow - Test Ports
      • Hydraulic Pressure Test Ports
      • Testing Relief Valve Pressures - Adjusting Relief Valves
      • How to Test and Adjust Main Control Valve Relief
      • How to Test and Adjust Pilot Pump Relief Valve
      • Testing and Adjusting Steering Circuit Relief Valve
      • How to Test Tilt Circuit Relief Valves
      • How to Test & Adjust Drive Circuit Relief Valves
      • How to Test Crowd Circuit Relief Valve
      • Testing the Brake Circuits
      • How to Test and Adjust the Inching System
      • How to Check and Adjust the Boom Cables
      • Boom Slider Pad Adjustment
      • How to Check and Tighten Boom Hoses
      • Hydraulic Circuit Table of Pressures
      • Torque Chart
      • Electric Schematic Drawing
      • Hydraulic Schematic Drawing
  • TROUBLE SHOOTING
    • 8360R Trouble Shooting Drive System
    • 28902 Char-Lynn Steering Control Units Trouble Shooting Guide
  • TRANSMISSION & TORQUE CONVERTER
    • SM HR 182-3 Clark 18000 Series Powershift Transmission
      • HOW THE UNITS OPERATE
      • SECTIONAL VIEWS AND PARTS IDENTIFICATION
        • Basic Design
        • Converter Group
        • Converter and Transmission Case Group
        • Two and Three Speed Gear and Clutch Group
        • Clutch Group
        • Control Valve Assembly
        • Parking Brake Group
        • External Plumbing Diagram
        • Assembly Instructions
        • Typical 3 Speed 18000 Cross Section
      • DISASSEMBLY OF TRANSMISSION
      • CLUTCH DISASSEMBLY
      • CLEANING AND INSPECTION
      • REASSEMBLY OF TRANSMISSION
      • SERVICING MACHINE AFTER TRANSMISSION OVERHAUL
      • TOWING OR PUSH STARTING
      • SPECIFICATIONS AND SERVICE DATA
      • LUBRICATION
      • TROUBLESHOOTING GUIDE
      • TYPICAL TWO AND THREE SPEED POWER FLOW
      • PRESSURE CHECK POINTS
      • CLUTCH AND GEAR ARRANGEMENT
      • DRIVE PLATE INSTALLATION
      • TRANSMISSION TO ENGINE INSTALLATION PROCEDURE
      • SPEED SENSOR BUSHING INSTALLATION
  • MISCELLANEOUS
    • 0009 Rim & Wheel Safety Manual
    • S5AWDB Soma Planetary w/Wet Disc Brake
      • Specifications
      • Special Tools
      • Disassembly of the Wheel end
    • S5AMM Soma Maintenance Manual
      • Corrections to this Manual
      • Recommended Lubrication Practices for Axles & Gear Boxes
      • Maintenance Recommendations
      • Differential Carrier
        • Adjustment of the Gear Set
      • Planetary Hub
      • Steering Parts
      • Specifications
        • Conversion Factors
    • TNP-1 Toe-in Procedure
    • W3-P Fairfield "A" Drive Torque Hub
    • F114004 Donaldson Cyclopac Service Procedure