Steele Products SP-PB306 - Manual (Page 6)

T o properly track the sanding belt:
1. Plug in the sander.
2. T urn power switch ON, then immediately OFF, noting whether the belt tends to slide off its
track, and to which side (front or back) of the sander.
3. If the sanding disc did not tend to either side, it is tracking properly.
4. If the sanding belt moves toward the disc (the front side of the sander), turn the tracking knob
clockwise ¼ turn.
5. If the sanding belt moves away from the disc (towards the back side of the sander), turn the
tracking knob counter clockwise ¼ turn.
6. T urn power switch ON, then immediately OFF again, again taking note of any belt movement.
7. Readjust tracking knob another ¼ turn, as necessary.
Installing or Changing Accessories – Sanding Discs
W ARNING! Turn the power off and remove the plug from the outlet before changing the accessories.
Note: Hook & Loop sanding discs cannot be used with this type of sander!
Removal:
1. Remove and set aside mitre gauge.
2. Completely remove the disc-sanding table.
Sanding discs are adhered to the plate
using a “pressure-sensitive adhesive”.
Remove sanding disc from disc plate.
Disc
Disc paper
11
Installation
1. Ensure disc-plate is clean.
2. Peel backing from new sanding disc.
3. -NAOOJASO=J@EJC@EO?łNIHUKJPK@EO?LH=PA
+KPAġ%KKG)KKLO=J@EJC@EO?O?=JJKP>AQOA@SEPDPDEOPULAKBO=J@AN
Replace the sanding table and handles that were removed in step 2 (above).
Dust Chute/Port – Operation
0=J@EJCKLAN=PEKJO=NAEJDANAJPHU@QOPU1KDAHLIEJEIEVAPDA=IKQJPKB@QOPPD=PAO?=LAOEJPKPDA
surrounding air, this Steele® sander is equipped with a 2-1/4” (57 mm) dust chute (aka: port) that
?=J>AA=OEHU?KJJA?PA@PK=@QOP?KHHA?PEKJOUOPAI&PEOOPNKJCHUNA?KIIAJ@A@PD=PQOANOAILHKU=
@QOP?KHHA?PEKJOUOPAISDAJQOEJCPDEO>AHP@EO?O=J@AN
2OAKB=I=OGKNNAOLEN=PKNEOOPEHHNA?KIIAJ@A@ARAJSDAJ=@QOP?KHHA?PEKJOUOPAIEOEJQOA
Operating Instructions
Safety - Locking ON/OFF Switch
1DANK?GAN,+,##LKSANOSEP?DEOHK?=PA@KJPDABNKJPKBPDAO=J@AN
=J@EJ?KNLKN=PAO=NAIKR=>HA
O=BAPUOSEP?D
1. -NAOOPDAOE@AI=NGA@,+PKPQNJPDAO=J@ANKJ
2. -NAOOPDAOE@AI=NGA@,##PKPQNJPDAO=J@ANKBB
&JOEPQ=PEKJOSDANAPDAO=J@ANI=U>AHABPQJ=PPAJ@A@
PDAKLAN=PKND=OPDAKLPEKJKBNAIKREJCPDA
ļUAHHKS‡O=BAPULKNPEKJKBPDA,+,##OSEP?DPKNAJ@ANPDAO=J@ANEJKLAN=>HA4DAJPDAKLAN=PKNEO
NA=@UPKQOAPDAI=?DEJA=C=EJ
PDAļUAHHKS‡O=BAPULKNPEKJKBPDAOSEP?DI=U>ANAEJOP=HHA@OEILHU>U
inserting it into the opening in the switch and pushing it in until it “seats”.
Operating Instructions – Belt Sander – Horizontal and Vertical Sanding
6KQN0PAAHAĮ>AHP@EO?O=J@AN„>AHPOP=PEKJ?=JO=J@RANPE?=HHU=OSAHH=ODKNEVKJP=HHU!ALAJ@EJC
KJKLAN=PKNJAA@O=J@PDASKNGLEA?A
PDASKNGOQLLKNP?=J>AQOA@SEPDAEPDANPDADKNEVKJP=HKN
vertical position.
1K?D=JCABNKIKJALKOEPEKJPKPDAKPDANġ
1. Locate the 15/64” (6 mm) hex wrench
2. )KKOAJPDA>A@HK?GEJCDATOK?GAPO?NAS>UPQNJEJCEP?KQJPAN?HK?GSEOA
3. *=JQ=HHUIKRAPDASKNGOQLLKNPOP=PEKJEJPKPDARANPE?=HKNDKNEVKJP=HLKOEPEKJ
=ONAMQENA@
4. /APECDPAJPDA>A@HK?GEJCDATOK?GAPO?NAS>UPQNJEJCEP?HK?GSEOAĠQOEJCPDA‡ĠII

hex wrench).
(See the following figures)
,LAN=PEKJ=H+KPAġ0=J@HKJCSKNGLEA?AOSEPDPDAO=J@EJC>AHPEJPDARANPE?=HLKOEPEKJ>UIKREJCPDA
SKNGARAJHU=?NKOOPDAO=J@EJC>AHP
12