Poison Spyder LED TAILLIGHTS & FLASHERS - Manual (Page 2)

INSTALLATION INSTRUC
TIO
NS
©2009 POISON SPYDER CUSTOMS, INC. • 951-849-5911 • WWW.POISONSPYDER.COM
Poison Spyder Customs • LED TAILLIGHTS & FLASHERS INSTALLATION Page 2
not to drill through any sheet metal where
the back side is exposed or visible. Sand or
grind the area where the terminal will contact
the sheet metal to ensure a positive contact.
6. Plug the LED lamp fixture into the wiring
harness pigtail, then check for operation
by switching on turn signals, running lights,
brakes. If you have not installed LED-
specific flashers yet, the flash speed may be
incorrect when checking turn signals at this
point. If any light is not working properly, use
a test light or meter to check continuity at
each of the connections you made, and re-
do as needed.
7. Secure any slack in the wiring harness with
zip ties, split-loom, etc.
8. Install the LED light by either slipping it
into the rubber grommet and pushing it into
the hole (push-in style) or by attaching with
screws (flange-mount style).
INSTALLATION NOTES:
• On CJ8, additional inner wheel well removal
is needed for flush-mount taillight install
• On ’03 and newer TJ’s, the passenger side
taillight may need to be inverted to clear
factory emissions equipment.
LED FLASHER INSTALLATION
LED’s require a special flasher module to provide
the correct current resistance for the LED’s as
opposed to the factory incandescent bulbs. If
you install LED’s without the correct flasher, you
will notice that your turn signals and flashers will
blink at a faster rate.
The correct LED flasher for each year model
Jeep will solve this problem, and is available
separately from Poison Spyder Customs. Each
LED flasher is an easy plug-in replacement for
the factory flasher.
Locations for the stock flashers are as follows:
1976-96 CJ/YJ: Under dash
1997-2000 TJ: Underneath and to the right of
the steering column, behind dash cover(s).
2001-06 TJ/LJ: On top of steering column,
under steering column cover.
1. Remove any dash or column covers (TJ/LJ)
2. Unplug the flasher from the harness.
3. Install Poison Spyder LED Flasher into the
stock flasher socket.
4. Check to ensure that all LED’s are working
properly.
5. Replace any dash or column cover(s) that
were removed in step 1.
WARRANTY
Poison Spyder Customs™ warranties all of
the products we sell and distribute for one (1)
year from the date of sale. These products will be
free from defects in material and workmanship
under normal installation, and use. Due to the
intended use the powder coat finish is warranted
for ninety (90) days. The finish warranty will not
cover a product if it has been damaged in any
way. Warranty is limited to repair or replacement.
Poison Spyder Customs™ does not offer any
type of labor or shipping allowance and all
warranty claims are subject to inspection by
Poison Spyder Customs™.
At the discretion of Poison Spyder Customs™,
the products in question can be repaired or
replaced when found defective. Prior to any
replacement or repair, written authorization must
be obtained from Poison Spyder Customs™.
CIRCUIT DRIVER WIRE PASS. WIRE* LED WIRE
back-up lamp violet/black violet/black do not use
running lights yellow/black yellow/black black
turn signal/brakes green/red brown/red red
(not used) green/red do not use
LED Ground N/A N/A white
*The Driver and Passenger side wire colors given are for the factory TJ taillight harness. If installing on a YJ, the wire colors given in the Driver’s side column apply to both sides.
NOTE: This is a general wiring diagram, there are variances through the years, even from driver side to passenger side.
Table 1: Wiring Connections -- Factory TJ Harness to LED Pigtail