Periodic maintenance, Engine maintenance, Ground pounder® maintenance – MBW 7000 Series User Manual

Page 11

Advertising
background image

9

PERIODIC MAINTENANCE

ENGINE MAINTENANCE

AIR CLEANER

1.

Your Compactor uses either a dry type air cleaner element or a

Dual" Oil-Foam and Paper Element. Clean the dry element or

Oil-Foam" element every 25 hours under normal conditions

and every few hours under extremely dusty conditions.
a.

Clean the dry element by tapping it lightly on a flat surface.

Keep tapping until no dust comes off. The element should

be replaced if the dust does not drop off easily or if the eleĆ

ment becomes bent or crushed.
Note: Do not wash elements in any liquid of blow dirt off

with air. Do not tap element on a sharp corner, it may damĆ

age the seal.

b.

Clean the Oil Foam" type element by washing it in keroĆ

sene or liquid detergent and water to remove the dirt. Wrap

the foam in a cloth and squeeze dry. Saturate the foam in

engine oil and squeeze it to remove excess oil. Assemble

the parts and reinstall air cleaner to engine.

SPARK PLUG

A dirty, oily or carboned spark plug makes starting difficult and causes

inefficient operation. Remove and clean spark plug as necessary (see

engine manual). Set spark plug gap as described in engine manual.

LUBRICATION

Clean dirt from around oil fill cap and check oil level. Oil level should

be between the FULL" and ADD" marks on the dipstick or to overflow

point in fill hole on engine without dipstick.
Change oil after first two (2) hours of operation, and after every

twenty-five (25) hours thereafter or at the end of each season. To

change oil, tilt machine back and place a pan to catch oil underneath

engine deck. Remove drain plug from engine and let oil drain into

pan.

If engine has been running, oil will be HOT! Where proĆ

tective gloves when working with engine oil.

CAUTION!

Replace engine drain plug and wipe oil off engine deck. Refill engine

with oil in accordance to recommendations found in engine manual.

ENGINE RPM

1.

The engine should be set at an operating speed of 3400 rpm.

Check engine owner's manual for procedure on setting operatĆ

ing speed.

2.

The idle speed of the engine must not exceed 1800 rpm. If the

idle speed is greater the clutch may not disengage. Check enĆ

gine owner's manual for procedure on setting idle speed.

GROUND POUNDER®

MAINTENANCE

GENERAL MAINTENANCE

1.

On a new Ground Pounder®, the exciter is pre-oiled at the factoĆ

ry, and needs no immediate attention.
a.

Replace exciter oil once every season or every 500 hours.

b.

The oil capacity of the exciter is 24 oz. (720ml)

c.

Use only MBW Ground Pounder® Exciter Oil available in

6 packs (#01058).

2.

Exciter Oil Change Procedure.

Oil in exciter is HOT after machine has been running!

Where protective gloves when working with oil.

CAUTION!

a.

Let engine cool before changing exciter oil.

b.

Remove belt guard and belt.

c.

Remove the 1/2" hex head cap screws from sided of plate

housing.

d.

Lift entire housing deck with engine from plate housing.

e.

Remove the 3/8" drain screw (Figure 2, item 20) from the exĆ

iter housing cover.

f.

Tilt plate housing upside down so oil drains from exciter

housing. (Examine oil for metal chips as a precaution to fuĆ

ture troubles.)

g.

Replace drain screw

h.

Tip plate housing upright and remove the 3/8" plug pipe on

top of the exciter. Fill using 24 oz. (720ml) of MBW Ground

Pounder® Exciter Oil (Oil can be purchased from your loĆ

cal MBW Distributor, part #01058). Replace the pipe plug!

i.

Install housing deck, belt and belt guard.

3.

Keep Plate Clean
a.

Remove excess soil which enters rear of plate.

4.

Belt Adjustment
a.

When belt stretch develops, loosen (do not remove) 4 enĆ

gine mounting screws, pull engine back. Retighten engine

bolts.

DISASSEMBLY PROCEDURE

1.

Engine Removal.
There are two methods of engine removal.
a.

To work on engine only, remove the belt guard, belt and 4

engine mounting screws.

b.

The second method is to remove the entire engine deck

(See b, c and d of exciter oil change)

2.

For Engine repair, see your Authorized Engine Dealer.

3.

Exciter Disassembly (Use Figure 2, Page 12)
a.

Remove engine deck per steps b, c and d under Exciter Oil

Change.

b.

Remove 4 exciter holdĆdown bolts and clean exciter before

proceeding with disassembly.

c.

Remove VĆpulley. If pulley is froze, go to the next step.

d.

Remove rear cover (item 3) by unscrewing the 6 flange

screws.

e

Block the exciter housing on large O.D. side, then press exĆ

citer shaft through housing.

f.

Remove front cover.

Note: Always replace oil seal (item 2) after any teardown.

g.

To remove the roller bearing in the rear cover, remove snap

ring (Item 5), then remove the two inner hex head cap

screws. Use two 1/4" dia pins 2" long placed in the 5/16"

threadded holes. Use square stock over the pind to bridge

and press out the bearing.

h.

When reassembling use new gaskets, items 23 & 24 or

FormĆAĆGasket" type compound.

Advertising