Service, Torque chart, Service tools – MBW V.E.U. User Manual

Page 11: Replacing shaft coupler, Ervice, Torque chart service tools replacing shaft coupler

Advertising
background image

- 8 -

S

ERVICE

Assembly and disassembly should be performed by a
service technician who has been factory trained on MBW
equipment. The unit should be clean and free of debris.
Pressure washing before disassembly is recommended.

• Prior to assembly, wash all parts in a suitable cleaner or

solvent.

• Check moving parts for wear and failure. Refer to the

Replacement section in this manual for tolerance and
replacement cycles.

• All shafts and housings should be oiled prior to pressing

bearings. Also, ensure that the bearings are pressed
square and are seated properly.

• All bearings should be replaced when rebuilding any

exciter or gearbox.

• All gaskets and seals should be replaced after any

disassembly.

Torque Chart

Service Tools

Replacing Shaft Coupler

Refer to Main Assembly, page 12.

1.

Remove the four nuts and bolts securing Silencer
inlet adapter (# 20) to the silencer(# 24)

2.

Remove the Blower End Side panel (# 10)

3.

Remove the air cleaner outer door.

4.

Loosen the six mounting bolts (# 55) which secure
the canister weldment to the frame. Remove all but
the front most bolt on the air cleaner side.

5.

Carefully pivot the blower end of the weldment away
from the engine, making sure not to stress any wiring
or cables. It will only be necessary to move the end
about 3” to remove the coupler (# 6).

6.

Replace the coupler and slide the canister back into
place, aligning the splines of the drivers and coupler.

7.

Ensure that the shoulders of the drivers are flush with
the ends of the coupler, and that the shafts are still
aligned.

8.

Replace the canister mounting bolts (# 55), sealing
the three bolts in the air filter end with silicone
sealant.

9.

Reinstall the four bolts securing the silincer inlet
adapter to the silencer and the blower end side panel.

SIZE

GRADE 2

GRADE 5

GRADE 8

1/4-20

49 in

•

lbs

76 in

•

lbs

9 ft

•

lbs

1/4-28

56 in

•

lbs

87 in

•

lbs

10 ft

•

lbs

5/16-18

8 ft

•

lbs

13 ft

•

lbs

18 ft

•

lbs

5/16-24

9 ft

•

lbs

14 ft

•

lbs

20 ft

•

lbs

3/8-16

15 ft

•

lbs

23 ft

•

lbs

33 ft

•

lbs

3/8-24

17 ft

•

lbs

26 ft

•

lbs

37 ft

•

lbs

7/16-14

24 ft

•

lbs

37 ft

•

lbs

52 ft

•

lbs

7/16-20

27 ft

•

lbs

41 ft

•

lbs

58 ft

•

lbs

1/2-13

37 ft

•

lbs

57 ft

•

lbs

80 ft

•

lbs

1/2-20

41 ft

•

lbs

64 ft

•

lbs

90 ft

•

lbs

9/16-12

53 ft

•

lbs

82 ft

•

lbs

115 ft

•

lbs

5/8-11

73 ft

•

lbs

112 ft

•

lbs

159 ft

•

lbs

5/8-18

83 ft

•

lbs

112 ft

•

lbs

180 ft

•

lbs

3/4-16

144 ft

•

lbs

200 ft

•

lbs

315 ft

•

lbs

1-8

188 ft

•

lbs

483 ft

•

lbs

682 ft

•

lbs

1-14

210 ft

•

lbs

541 ft

•

lbs

764 ft

•

lbs

1-1/2-6

652 ft

•

lbs

1462 ft

•

lbs

2371 ft

•

lbs

M 6

3 ft

•

lbs

4 ft

•

lbs

7 ft

•

lbs

M 8

6 ft

•

lbs

10 ft

•

lbs

18 ft

•

lbs

M 10

10 ft

•

lbs

20 ft

•

lbs

30 ft

•

lbs

CONVERSIONS

in

•

lbs x 0.083 = ft

•

lbs

ft

•

lbs x 12 = in

•

lbs

ft

•

lbs x 0.1383 = kg

•

m

ft

•

lbs x 1.3558 = N

•

m

PART NO.

DESCRIPTION

19279

KIT, SENSOR CALIBRATION

20350

SERVICE KIT, VEU, ISUZU

SIZE

GRADE 2

GRADE 5

GRADE 8

Advertising