Mountain Off Road BLYJ8795 - Manual (Page 2)

7. After all of the pucks and longer bolts are in place, tighten the bolts. Use Your judgement as to how
tight. Do not over tighten them, but do not leave them loose. Do not “crush” the rubber insulators.
8. Locate the front grille support that is welded on the round frame crossmember ( location1 ). Drill
two holes 3/16” in diameter on the top of this support about 3/4” in from the edge and just in front of
the grille. Insert the two plastic clamps that you removed from the steel strip in step 2 in the holes
you just drilled. Snap the steel brake line into the clamps. Discard the steel strip removed in step 2.
Re-attach the plastic frame cover if so equipped.
9. Hold the shroud to the radiator one inch lower then the original mounting location. Mark the holes.
Center punch them and drill a small pilot hole. Now, enlarge them to 5/16” in diameter. Re-attach
the shroud to the radiator in the new holes drilled.
10. If your Jeep has stock suspension (no lift) you are finished ! If your Jeep has a suspension (lift) kit
that incorporates a drop skid pan ( crossmember under the transmission/transfer case), installation
of this body lift kit may cause the transmission shift lever to contact the floor (body) of your Jeep.
To keep this from happening , you must perform the following: Remove the shift lever boot from the
floor pan and trim the sheet metal with tin snips until the transmission can be shifted into 2nd, 4th
and reverse gears without interference. The boot has a metal ring molded into it’s base and it will
need to be located back approx. 3/4” or more on the floor by re-drilling the mounting holes. Fill any
gaps in the floor with black silicone.
IF YOU PURCHASED A BODY LIFT SYSTEM THAT INCLUDED REPLACEMENT
POLYURETHANE BODY MOUNTS, THE FOLLOWING CHART INDICATES
THE PROPER LOCATION OF THE INSULATORS:
FRONT OF VEHICLE REAR OF VEHICLE
Your are now finished ! Please re-check all mounting hardware on a frequent basis and after every
off road trip.
TERMS-POLICIES:
RETURNS: No returns will be accepted without prior permission from M.O.R.E.™ LLC. After you receive a Return Goods Authorization (RGA) number, merchan-
dise must be returned prepaid and insured. A claim must be made with in 30 days from receipt of merchandise. The original invoice or a copy with the RGA number
written on must accompany all returns. A 20% restocking fee will be charged on all parts returned for credit or refund unless merchandise is proven to be defective
or was shipped wrong by M.O.R.E.™ LLC. No merchandise will be issued credit or refund if it has been installed, modified, used in any way or is in unsalable condi-
tion.
WARRANTY: All merchandise is warranted to be free from defects in materials and workmanship prior to installation. Any alteration or improper use will void this
warranty. Because all parts we sell are intended for use in heavy-duty applications it is not possible to warrantee or guarantee the performance of any items.
M.O.R.E.™ LLC. products and the products manufactured by others, which we sell may be subject to an infinite variety of conditions due to the manner in which
they are used, serviced and/or installed. Purchasers and users of such products rely upon their own judgment as to the suitable use selection, service and installa-
tion of such products.
PRODUCT DISCLAIMER: Modification of your vehicle to enhance performance with parts sold by M.O.R.E.™ LLC. may create a dangerous condition which could
cause serious bodily injury, and the buyer hereby expressly assumes all risks associated with any such modifications. All parts sold by M.O.R.E.™ LLC. are for
racing or off road use only. Mountain Off Road Enterprises LLC. will not accept responsibility for personal injury or property damage arising from the failure of any
parts manufactured or sold by M.O.R.E.™ LLC.
Specifications are subject to change without notice.
Jeep® , YJ® , Wrangler® , are registered trademarks of DaimlerChrysler .
M.0.R.E.™ is a trademark used by Mountain Off Road Enterprises, LLC. The M.O.R.E.™ logo and these instructions are copyright© , 2008.
Page 2 of 2