JLG 500RTS ANSI Operator Manual - Manual (Page 18)

SECTION 2 - PREPARATION AND INSPECTION
2-6 – JLG Sizzor – 3121100
GENERAL
Begin the “Walk-Around Inspection” at Item 1, as noted
on the diagram.Continue to the right (counterclockwise
viewed from top) checking each item in sequence for the
conditions listed in the “Walk-Around Inspection Check-
list”.
TO AVOID INJURY DO NOT OPERATE MACHINE UNTIL ALL MAL-
FUNCTIONS HAVE BEEN CORRECTED. USE OF A MALFUNC-
T I O N I N G M A C H I N E I S A S A F E TY V I O LATI O N. TO AV O I D
POSSIBLE INJURY, BE SURE MACHINE POWER IS “OFF” DUR-
ING “WALK-AROUND INSPECTION”.
NOTE: Do not overlook visual inspection of chassis under-
side. Checking this area often results in discovery of
conditions which could cause extensive machine
damage.
1. Steer Cylinder and Tie Rod Ends - No loose or
missing parts, no visible damage. No steer cylinder
leaks or damage.
2. Leveling Jack, Left Front (If Equipped) - No loose or
missing parts, no visible damage. No cylinder leaks
or damage.
3. Drive and Lift Cutout Switches (If Equipped) - No
visible damage, properly secured.
4. Steer Spindle, Left Front - No loose or missing
parts, no visible damage, evidence of proper lubri-
cation.
5. Steer/Drive Wheel and Tire Assembly, Left Front -
Properly secured, no loose or missing lug nuts, no
visible damage. Refer to inflation psi stenciled on
frame.
6. Drive Motor, Left Front (4 Wheel Drive) - No visible
damage, no evidence of leakage.
7. Drive Brake, Left Front (4 Wheel Drive) - No loose or
missing parts, no visible damage, no evidence of
leakage.
8. Drive Hub, Left Front (4 Wheel Drive) - No visible
damage, no evidence of leakage. Drive hubs
should be one half full of EPGL SAE 90.
9. Traversing Platform Extension Cylinder (If
Equipped) - Properly secured, no visible damage,
no loose or missing parts, no evidence leakage.
10. Oscillating Axle (If Equipped) - Properly secured,
evidence of proper lubrication. No lockout cylinder
leaks or damage.
11. Ladder - No damage, securely attached.
12. Hydraulic Reservoir - No visible damage or missing
parts. No evidence of leaks. Recommended oil
level in sight glass. Breather cap secure and work-
ing.
13. Ground Controls - Switches operable, no visible
damage, placards secure and legible.
14. Tilt Alarm Switch - Properly secured, no loose or
missing parts, no visible damage.
15. Hydraulic Filter - No visible damage, properly
secured, no evidence of leakage.
16. Auxiliary Power Pump - Properly secured, no visible
damage, no evidence of leakage. Hoses and fit-
tings properly secured, no visible damage, no evi-
dence of leaks.
17. Control Valves - Valves properly secured, no visible
damage, no evidence of leakage. Hoses and fit-
tings properly secured, no visible damage, no evi-
dence of leaks.
18. Hand Pump Manual Descent - Properly secured, no
loose or missing parts, no visible damage.
19. Fuel Tank (Gasoline or Diesel Engine) - Filler cap
secure, sight gauge visible, no damage or leaks.
20. Traversing Platform Extension Cylinder (If
Equipped) - Properly secured, no visible damage,
no loose or missing parts, no evidence leakage.
21. Travel/Descent/Motion Alarm - Properly secured, no
loose or missing parts, no visible damage.
22. Safety Prop - Stored securely, no missing parts.
23. Drive Wheel and Tire Assembly, Left Rear - Properly
secured, no loose or missing lug nuts, no visible
damage. Refer to inflation psi stenciled on frame.
24. Drive Motor, Left Rear - No visible damage, no evi-
dence of leakage.
25. Drive Brake, Left Rear - No loose or missing parts,
no visible damage, no evidence of leakage.
26. Drive Hub, Left Rear - No visible damage, no evi-
dence of leakage. Drive hubs should be one half full
of EPGL SAE 90.
27. Steer Spindle, Left Rear (If Equipped) - No loose or
missing parts, no visible damage, evidence of
proper lubrication.
28. LP Tank and Bracket (If Equipped) - No loose or
missing parts, no visible damage. No leaks or dam-
age.
Figure 2-2. Walk-Around Inspection Points (Sheet 1 of 3)