JLG 1250AJP Quick Reference Guide - Manual

1250AJP Quick Reference
Getting Started Controls and Indicators
Footswitch/Enable
Axles
Drive Orientation Override 1
2
3
4
5
6
7
8
Select platform controls
Pull out both E-Stops
Start Engine
Below 20°F (-7°C) run engine for
15 min. before operating machine.
Verify axles are extended
before lifting boom.
Select appropriate platform
capacity
Enable footswitch
Operate Machine
- Ground Station
- Platform Station Located at:
To enable the platform controls, step on the footswitch FIRST and then choose a function within
7 seconds. If no function is selected within 7 seconds, the Footswitch/Enable light will turn off and
the footswitch must be released and depressed again.
Axles must be extended and the Axle Set Light must be on to elevate the boom. To extend the axles,
select the axle extend switch while driving forward or reverse.
If operating drive and the Drive Orientation Light flashes, the drive controls may be opposite from the
the Drive Orientation Override switch, and 3) operate drive within 3 seconds.
When the Platform Capacity is selected to the 500 lb (230 kg) position, the 500 lb
(230 kg) light will be on and the JLG control system will allow operation within the larger
envelope. The side swing jib can be used with this selection.
Platform Capacity Select/Jib Swing Function
Note: If both capacity lights are flashing, the boom or jib is out of the allowable
envelope. Remove platform load over of 500 lb (230 kg) and select the 500 lb
(230 kg) capacity position.
When the Platform Capacity is properly selected to the 1000 lb (450 kg) position, the
1000 lb. (450 kg) light will be on, and the JLG control system will allow operation within
The smaller envelope. This side swing jib must remain in the centered position with
Tower Lift Control Tower Lift Control
Platform leveling
Auxilary Power
While operating tower lift, the JLG control system will also coordinate the movement of the main
boom within its allowable limits. While operating tower lift up, the main boom will also lift up.
While operating tower lift down, the main boom will also lift down. The main boom can also be
positioned manually using the main lift controller.
Lift and telescope movements of the tower boom are coordinated by the JLG control system.
While operating tower lift up, the tower boom will also telescope out. While operating tower lift down,
the tower boom will also telescope in.
Platform leveling is controlled by the JLG control system to maintain a set platform position.
This feature is active during
and drive movements. The starting platform position can lift, swing,
be manually adjusted using the platform level override switch.
Note: Movements of the boom using auxiliary power will be SLOW and the movements
will momentarily stop and alternate between other functions as needed. When operating
Tower Lift, the movements will alternate between tower lift, tower telescope, and main
lift. When operating Main Lift, the movements will alternate between main lift, tower lift,
and platform level.
To operate a function using Auxiliary power, operate the function while activating the auxiliary
power switch.
Boom Control System Warning
If operating a function causes the Boom Control System Warning Light to flash and the platform
alarm to sound, the selected movement is not allowed. To continue movement, operate the
function in the opposite direction, or operate a different function.
!
JLG - 3128413 - 7-21-2010
500 lb MAX
230 kg MAX
1000 lb MAX
450 kg MAX
Creep Speed
WARNING!
The creep light acts as a reminder that all functions are set to the slowest speed. The light will be
on continuously if the creep switch is selected by the operator. The creep light will flash if the JLG
control system has selected this creep speed automatically. This occurs when the boom is near the
Edge of the envelope, when the hydraulics are cold, or the Boom Control System Warning is active.
500 lb MAX
230 kg MAX
1000 lb MAX
450 kg MAX
STEP
STEP
STEP
STEP
STEP
STEP
STEP
STEP
intended driving direction. To continue: 1) verify the intended drive direction, 2) push and release
this selection.
The Boom Control System Warning Light may indicate contact of
the machine with another structure and continued movement may
result in damage to the machine or machine tip over.
Read the Operation and
Safety Manual. Perform
pre-start inspection.
CE/AUS