Echo 76624 Owners Manual v.3 - Manual (Page 4)

2 6 INCH CHIPPER
Table of conTenTs
descriPTion Page descriPTion Page
safeTY ......................................................................... 3
1.1 SaFety aleRt SyMbol ........................................ 3
1.2 eMISSIoN INFoRMatIoN ....................................... 3
1.3 beFoRe oPeRatING .............................................. 4
1.4 oPeRatIoN SaFety .............................................. 4
1.5 Feed RolleR SaFety .......................................... 5
1.6 MaINteNaNCe SaFety ......................................... 5
1.7 toWING SaFety ..................................................... 5
1.8 StoRaGe SaFety .................................................. 5
1.9 batteRy SaFety ................................................... 5
1.10 SaFety deCal loCatIoNS ................................ 6
1.11 SaFety deCalS .................................................. 7
assemblY .................................................................... 8
2.1 attaCh tRaIleR WheelS .................................... 8
2.2 attaCh dISChaRGe Chute ................................. 8
2.3 attaCh tRaIleR hItCh ......................................... 8
2.4 INStall ReaR StabIlIzeR .................................... 9
2.5 CheCk batteRy..................................................... 9
2.6 FIll the taNk ......................................................... 9
2.7 CheCk hydRaulIC FluId level ...................... 10
2.8 CheCk CoolaNt (dIeSel oNly) ....................... 10
2.9 CheCk MotoR oIl level .................................. 10
feaTures & conTrols .......................................... 11
3.1 CoNtRol PaNel .....................................................11
3.2 ChIPPeR FeatuReS .............................................. 12
oPeraTion ................................................................ 14
4.1 StaRtING a GaSolINe ChIPPeR ...................... 14
4.2 StaRtING a dIeSel ChIPPeR ............................ 14
4.3 MovING Chute aNd dISChaRGe CaP ............. 15
4.4 beGINNING to ChIP ............................................. 15
4.5 lIMb SeleCtIoN aNd FeedING ......................... 16
4.6 ReMovING jaMMed MateRIalS ....................... 16
4.7 SMaRt Relay ....................................................... 16
4.8 Feed RolleR CoNtRol baR ............................ 17
4.9 StoPPING the ChIPPeR ...................................... 17
service & mainTenance ....................................... 18
5.1 MaINteNaNCe SChedule.................................. 18
5.2 CheCkING aNd ReMovING bladeS .................. 19
5.3 WheN to RePlaCe bladeS .............................. 19
5.4 ShaRPeNING the bladeS ................................. 19
5.5 INStallING the bladeS .................................... 19
5.6 RePlaCING the dRIve belt .............................. 20
5.7 RePlaCING hydRaulIC dRIve belt ................. 21
5.8 FIllING CoolaNt (dIeSel) ................................. 21
5.9 GReaSING .............................................................. 22
5.10 adjuStING the ChIPPeR aNvIl ...................... 22
5.11 FIllING hydRaulIC FluId ................................ 23
5.12 aIR FIlteR (dIeSel ShoWN)............................. 23
5.13 ChaNGING hydRaulIC oIl FIlteR ................. 23
5.14 tRaIleR SeRvICe tIPS...................................... 23
TroubleshooTing ................................................. 24
sPecificaTions ........................................................ 25
7.1 ChIPPeR SIze SPeCIFICatIoNS ......................... 25
7.2 eNGINe ModelS .................................................. 25
7.3 bolt toRQue ....................................................... 26