Preparation – Bose AM267565 User Manual

Page 10

Advertising

Preparation

• Each speaker enclosure extends

into the wall or ceiling

, as shown in the gray DO NOT CUT

area on the template (Figure 7), and below the grille. The speaker enclosure can be inserted
either up or down.

Note:

In cold climates where a humidifier is used, avoid inserting the speaker upside-down

in an exterior wall to prevent problems with condensation.

Allowing enough room both above and below the hole you draw provides a fallback in case
the area below your pilot hole is not suitable for the speaker enclosure.

Figure 7

Template for either
rectangular-faced (left)
or round-faced (right)
speakers

CAUTION:

When installed, the speaker enclosure cannot be seen behind the wall or ceiling.

Do not attempt to nail, cut, or drill on that surface area. Puncturing the speaker enclosure with
a tool will seriously damage the speaker.

• All electrical wiring, vents, and plumbing pipes located inside the walls must be avoided

(Figure 8). Check with a trained professional if you need instructions on how to locate and
avoid them.

Figure 8

Cautions against unseen
danger, such as (a) electri-
cal wires or (b) plumbing
pipes, behind the wallboard

• Use of a stud finder can help ensure that the speaker hole is at least 4

" (12 cm) from a

stud or joist.

• The selected location should be at the height you want for both speakers and where you

can maintain the minimum distance of 5 feet (1.5 m) between them.

Keeping in mind the guidelines given:

Decide where the first speaker will go.

Select the location for the second speaker.

Use the provided template for drawing both a pilot hole and the speaker-face outline.

" (14 cm)

DO NOT

CUT AROUND

GRAY AREA

" (20.5 cm)

" (36.9 cm)

TAPE

HERE

TAPE

HERE

TAPE

HERE

WHITE CUT OUT AREA

Pilot Hole

WARNING: Make sure the spot chosen is safe for cutting. Do not cut through
surfaces that have hazards, such as electrical wiring, conduits or plumbing,
concealed behind them. If you are not sure, consult a professional installer
before you proceed.

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

E n g l i s h & Tr a n s l a t i o n s

WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical
wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed.

WARNING: Make sure the spot chosen is safe for

drilling. Do not cut through surfaces that have hazards
concealed behind them, such as electrical wiring,
conduits or plumbing. If you are not sure, consult a
professional installer before you proceed.

WARNING: Make sure the spot chosen is safe for

WARNING: Make sure the

spot chosen is safe for
drilling. Do not cut through
surfaces that have hazards
concealed behind them,
such as electrical wiring,
conduits or plumbing. If you
are not sure, consult a
professional installer before
you proceed.

WARNING: Make
sure the spot chosen
is safe for drilling. Do
not cut through
surfaces that have
hazards concealed
behind them, such
as electrical wiring,
conduits or
plumbing. If you are
not sure, consult a
professional installer
before you proceed.

WARNING: Make sure the spot chosen is safe

for drilling. Do not cut through surfaces that have
hazards concealed behind them, such as
electrical wiring, conduits or plumbing. If you
are not sure, consult a professional installer
before you proceed.

WARNING: Make sure the spot

chosen is safe for drilling. Do not cut
through surfaces that have hazards
concealed behind them, such as
electrical wiring, conduits or plumbing.
If you are not sure, consult a
professional installer before you
proceed.

9" (22.9 cm)

TAPE

HERE

Translations below

TAPE

HERE

TAPE

HERE

TAPE
HERE

WHITE CUT OUT AREA

Pilot Hole

WARNING: Make sure the spot chosen is safe for cutting.
Do not cut through surfaces that have hazards, such as
electrical wiring, conduits or plumbing, concealed behind
them. If you are not sure, consult a professional installer
before you proceed.

DO NOT

CUT AROUND

GRAY AREA

WARNING: Make sure the spot chosen is safe for cutting. Do not cut through surfaces that have hazards, such as electrical
wiring, conduits or plumbing, concealed behind them. If you are not sure, consult a professional installer before you proceed.

WARNING: Make sure the spot chosen is safe for

WARNING: Make sure the spot

TAPE
HERE

Translations below

TAPE
HERE

E n g l i s h & Tr a n s l a t i o n s

TAPE
HERE

WARNING: Make sure the spot

TAPE

HERE

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

DO NOT

CUT AROUND

GRAY AREA

NOT FOR CUTTING

Large gray area

represents space to

reserve behind the wall

for the speaker

enclosure.

On the template at right,

small gray tabs also

indicate where not to cut.

FOR CUTTING

Large white area

represents what to cut

out for the speaker face.

On the template at right,

small circles outside the

white area indicate

additional holes needed

for the round-faced

speaker only.

(a)

(b)

AM267565_01_V.pdf May 13, 2003

Advertising

Popular Brands

Popular manuals