Atop Technology AW5500C Installation Guide - Manual (Page 2)

Warranty Policy
Warranty Conditions
Products supplied by Atop Technologies are covered in this warranty for
sub-standard performance or defective workmanship. The warranty is
not, however, extended to goods damaged in the following
circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock,
earthquake
(c) Use of unqualified power supply, connectors, or unauthorized
parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" number from Atop
before shipping the goods to be repaired to Atop. When in normal use,
a sold product shall be replaced with a new one within 3 months after
purchase. The shipping cost from the customer to Atop will be
reimbursed by Atop.
After 3 months and still within the warranty period, it is up to Atop
whether to replace the unit with a new one; normally, as long as a
product is under warranty, all parts and labor are free of charge to the
customers.
After the warranty period, the customer shall cover the cost for parts
and labor.Three months after purchase, the shipping cost from the
customer to Atop will not be reimbursed, but the shipping cost from
Atop to the customer will be paid by Atop.
Limited Liability
Atop shall not be held responsible for any consequential losses from
using Atop’s product.
Warranty
5 Years
3 Years
Product Categories
Ethernet Switches
Wireless
Serial Device Servers
Modbus Gateways
Embedded Device Servers
DIN-Rail Power Supplies
Power Adaptors
Antennas
Other Accessories
1 Year
Warranty Period
─ Any changes to this material will be announced on Atop website. ─
The warranty certification will not be effective until an authorized stamp
issued by Atop’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number:
ATOP Customer Services and Supports
1. Please contact your local dealers or Atop Technical Support Center at
the following numbers.
+ 886-3-550-8137 (Atop Taiwan)
+ 86-21-6495-6232 (Atop China)
2. Please report the defected problems via Atop’s Web site or E-mail
account
Web Site：www.atop.com.tw, e-mail：[email protected]
Web Site：www.atop.com.cn, e-mail：[email protected]
■ Unit Dimensions and Layout (unit=mm)
Device Dimensions,
Physical appearance and Mounting
Proceed to mount the AW5500C in a dry location free from dirt and
corrosive vapors, for more questions on environmental limitations
please refer to the User’s manual.
LED indicators
Color
Green
Orange
Red
Orange
Green
Green
Orange
Green
Green
Green
Status
On
Blinking
Off
On
Blinking
Off
On
Blinking
Off
On
Blinking
Off
On
Blinking
Off
Blinking
Off
Blinking
On
Off
Blinking
On
Off
On
Blinking
Off
Off
Blinking
Steadily
Blinking
Rapidly
Regular
AP Mode
WDS Bridge
Mode
AP Client
Mode
P2P
Locate
LAN
WLAN
RUN
Enabled
Enabled / No wireless client
Disabled
Enabled / WDS connected
Enabled / No WDS connected
Disabled
Enabled and connected to an AP
Enabled but not connected to an AP
Disabled
Device’s WPS mode is connecting in AP mode
WPS is connecting at Soft AP mode
WPS connection failed
Device’s WPS P2P mode is connecting in
AP client mode
WPS is connecting at client mode
WPS connection failed.
Being located
Not being located
Data is transmitting on Ethernet
Ethernet is connected on 100Mbps
Ethernet is disconnected on 100Mbps
Data is transmitting on Ethernet
Ethernet is connected on 10Mbps
Ethernet is disconnected on 10Mbps
Enabled
Enabled and data is transmitting
Disabled
System is not powered on
AP firmware is running normally
AP firmware is not running
Description
Left Side View Right Side View
Rear View Front View
Top and Bottom View
ANT1
Regular AP
WDS Bridge
AP Client
P2P
P2P
LAN
Reset
Locate
RUN
WLAN
Name
* In Wireless+ AP Mode, AP LED and WDS Bridge LED will go on together.
* If WLAN (radio) is turned off, mode LEDs(AP,WDS Bridge, and AP Client) should
all go off.