BLITZ SD Meters - Manual (Page 3)

ＰＲＥＳＳ sensor
ＴＥＭＰ sensor
OIL SENSOR ATTACHMENT
Multiple sizes available.
Refer to BLITZ homepage/Catalogue/
Optional parts/Repair parts section in ths manual.
Engine Block
Press sensor
Install on the high pressure fuel delivery hose between fuel tank
and fuel pressure regulator, using 3-way adaptor from auto parts shop.
Sensor Installation
Install the sensor onto the surface away from the source of heat and vibration. ①
Divide the vaccuum hose from the stable vaccuum source using supplied 3-way connector,
such as between the fuel pressure regulator and surge tank. ②
Connect the sensor and 3-way using supplied vaccuum hose. ③
Loose connection can cause vaccuum leak resulting engine damage.
Use supplied zip tie or hose bands to keep secure connection. □
To avoid the wiring from getting damaged, be careful not to bend
the wiring at the base of the sensors. □
Fuel Pressure Regulator
Fuel Delivery Pipe
Cut hose
3-way Joint
To surge tank
Sensor
Sensor
Screw size 1/8PT
※Apply sealing tape
to avoid the leak.
Aluminum washer
Oil Pan
TEMP SENSOR FITTING
Multiple sizes available.
Refer to BLITZ homepage/Catalogue/
Optional parts/Repair parts section in ths manual.
Caution ！
Install sensor securely with seal tape to avoid oil leak.
Check for any oil leak before driving.
Driving with oil leak can result the damage to the vehicle and/or vehicle fire. □
To avoid the wiring from getting damaged, be careful not to bend
the wiring at the base of the sensors. □
To avoid the wiring from getting twisted, connect the sensor and sensor harness
after installing the sensor in the fitting and oil pan. □
Sensor
Screw size 1/8PT
※Apply sealing tape
to avoid the leak.
COOLING PERFORMER
(With water temp sensor attachment)
Available for variety of JDM cars
Refer to BLITZ homepage/
Catalogue for application.
Radiator
Install sensor securely with seal tape to avoid oil leak.
Check for any coolant leak before driving.
Driving with coolant leak can result the damage to the vehicle. □
Make sure to refill the coolant after the installation is complete.
Low coolant can lead to overheat, resulting in engine damage. □
To avoid the wiring from getting damaged, be careful not to bend
the wiring at the base of the sensors. □
To avoid the wiring from getting twisted, connect the sensor and sensor harness
after installing the sensor in the fitting and radiator hose. □
Secure the temperature sensor to COOLING PERFORMER or aftermarket radiator hose
with hose band to avoid the coolant leak.
Driving with coolant leak can result the damage to the vehicle. □
Screw size 1/8PT
※Apply sealing tape
to avoid the leak.
Make sure to have enough space surrounding the oil filter area to avoid any interferences
with other engine component. □
Install sensor securely with seal tape to avoid oil leak.
Check for any oil leak before driving.
Driving with oil leak can result the damage to the vehicle and/or vehicle fire. □
Refill the oil to adequate level after installing the sensor. □
To avoid the wiring from getting damaged, be careful not to bend
the wiring at the base of the sensors. □
To avoid the wiring from getting twisted, connect the sensor and sensor harness
after installing the sensor in the fitting and oil pan. □
To avoid the wiring from getting damaged, be careful not to bend
the wiring at the base of the sensors. □
To avoid the wiring from getting twisted, connect the sensor and sensor harness
after installing the sensor in the fitting and fuel line. □
Install sensor securely with seal tape to avoid fuel leak.
Check for any fuel leak before driving.
Driving with fuel leak can result the damage to the vehicle and/or vehicle fire. □
Make sure to relieve fuel pressure before cutting the fuel line.
Pressurized fuel can spurt out and cause the vehicle fire. □
Screw size 1/8PT
※Apply sealing tape
to avoid the leak.
In case of turbocharged vehicle In case of normally aspirated vehicle
Tip of the sensor should be
at the centor of the center of the exhaust manifold.
DO NOT LOSE THE STOPPER RING!
Tap the thread into
either better position
Install oin the joining area
of the manifold
Exploded view
To avoid the burn, install when the engine is cold. □
Make sure to clean the exhaust manifold and turbocharger after installing to
avoid the damage to engine and/or turbocharger. □
To avoid the wiring from getting damaged, be careful not to bend
the wiring at the base of the sensors. □
To avoid the wiring from getting twisted, connect the sensor and sensor harness
after installing the sensor in the fitting and fuel line. □
Secure the wiring harness from heat source to avoid the damage. □
Tap the screw thread (1/8 PT) into the exhaust manifold.
(If there is not enough thickness, weld the fitting onto the manifold.) ①
Screw size1/8PT
□ （Oil Temperature）
□
□
□ （Fuel pressure）
□ （Water temp）
Oil Filter
Avoid overtightening the sensor. □
Avoid overtightening the sensor. □
□ （Oil temperature and pressure）
Caution ！
Caution ！
Caution ！
Caution ！
Caution ！