Britax Verve - Manual (Page 3)

vigour
1A 1B 1C 1D
1A Open stroller by holding the handle
and lifting upwards, fully extending the
chassis until it clicks into position.
WARNING: Ensure chassis locking devices
are engaged before use.
1B Apply brake when assembling the
stroller. To lock the brake, push the brake
lever down. To unlock the brake, lift brake
lever up.
IMPORTANT: Always apply brakes when
parking the stroller.
1C To attach the arm bar, align moldings
on the arm bar with the metal tabs on
the stroller. Slide both arm bar moldings
down until fully engaged. Check for proper
installation by carefully pulling on the arm
bar.
To remove arm bar, remove hood (if fitted)
and slide both arm bar moldings up and off
the metal tabs on the stroller until released.
WARNING: DO NOT lift stroller by the
arm bar or hood as it may disengage.
1D To attach the hood with the arm bar
in place, align the hood moldings with the
plastic tabs on the arm bar and slide them
down until fully engaged.
The hood can be fitted without the arm
bar by aligning the moldings on the hood
with the metal tabs on the stroller frame
and sliding them down until fully engaged.
To remove hood, slide the moldings
upwards until released from the tabs on
the arm bar or stroller.
1E To open the hood, pull the front of the
hood forward then push the hood hinges
on both sides of the hood down. To close
hood, reverse above directions.
1E
1G To secure the child in the 5-point
harness, push buckles (A) into buckle
housing (B) until buckle prongs snap into
position. Carefully adjust the harness
by pulling sliders (C) until desired fit is
achieved in waist belt, shoulder belts and
crotch strap.
To release buckles (A), squeeze top and
bottom prongs.
WARNING: Always use crotch strap in
combination with waist belt. Always adjust
harness when changing child’s seating
position.
WARNING: Fasten harness when not in
use to prevent it from becoming trapped
when folding the stroller.
1G
1H To raise shoulder harness height, pull
harness straps through harness height
adjuster so that they lay flat on top of the
harness height adjusters.
To lower shoulder harness height, thread
harness straps through harness height
adjuster so they lay flat against the seat
back, under the harness height adjuster.
1H
1F To recline the backrest, squeeze and
release the buckle at the end of the short
strap from the buckle housing. Pull the
seat-back down and insert the buckle at
the end of the longer strap into the buckle
housing. To recline the backrest further,
release the buckle from the buckle housing
and pull the seat-back down.
Reverse the above directions to return the
backrest to an upright position.
IMPORTANT: Always support the seat
back when adjusting the angle.
1F
2A Apply brake before folding the stroller.
Press and hold safety button on release
latch while simultaneously pulling up on
release latches.
WARNING: Always remove your child from
the stroller prior to folding of stroller.
2C
Fully close and store stroller in a safe,
dry space.
IMPORTANT: Do not fold and store the
stroller when damp. Stroller should be dry
before folding and storing.
2B Push handle downward until the
stroller folds in half.
vigour 1. Using your stroller
2. Folding the stroller
2A 2B 2C
5-Point Harness
Basket
Arm Bar
Hood
Brake Lever
Hood Hinge
Handle
Swivel
Wheel Lock
Front Swivel Wheel
Backrest
Adjustment
Release Latch
with
Safety Button
vigour Introducing your new stroller
Leg Rest
1I
1I To lock the front swivel wheel, push
front swivel lock from right to left. To
unlock, push front swivel lock from left to
right.
Harness
Height Adjuster
A
B
C