Johnson Systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1210/620) - Manual (Page 27)

www.johnsonsystems.com 27
39. HARD-KEY View the microcontroller’s unique six-character hard-key code.
JS-ICON ™ Series dimmer racks may be shipped with an invalid hard-key code of
000000. A valid hard-key must be entered before the run time (RTIME) counter
reaches 2160 hours / 90 days. If the run time expires without a valid hard-key the
LCD display will show a runtime counter error (RTC ERR!) and all dimmer control
outputs will be disabled.
HARD-KEY A dash (-) between hard and key represents a valid hard-key.
HARD KEY A blank space between hard and key represents an invalid hard-key.
K:XXXXXX Shows the unique six-character hard-key code (XXXXXX).
K:XXXXXX Follow the procedure below to enter the menu and modify the hard-key.
K:XXXXXX Press and hold EXECUTE and then ESCAPE at the same time for 4-5 seconds.
K>XXXXXX A pointer (>) appears to indicate hard-key modification is activated.
K>XXXXXX Press MENU ( ) to modify the first hard-key character.
K:>XXXXX Press EXECUTE to advance to the second hard-key character.
K:>XXXXX Press MENU ( ) to modify the second hard-key character.
K:X>XXXX Press EXECUTE to advance to the third hard-key character.
K:X>XXXX Press MENU ( ) to modify the third hard-key character.
K:XX>XXX Press EXECUTE to advance to the fourth hard-key character.
K:XX>XXX Press MENU ( ) to modify the fourth hard-key character.
K:XXX>XX Press EXECUTE to advance to the fifth hard-key character.
K:XXX>XX Press MENU ( ) to modify the fifth hard-key character.
K:XXXX>X Press EXECUTE to advance to the sixth hard-key character.
K:XXXX>X Press MENU ( ) to modify the sixth hard-key character.
Press ESCAPE to exit the menu and save the desired hard-key code.
Press RESET to exit the menu without saving.
The menu will automatically timeout after 2 minutes of inactivity and save.
NOTE: Be sure to record and file the hard-key code on page 31 for future reference.
40. SERIAL# View the microcontroller’s unique six-character silicone serial number.
XXXXXX Shows the unique six-character serial number.
41. VERSION View the microcontroller’s software version.
VER X.X Shows the microcontroller’s software version.
42. EEPROM View the type of EEPROM memory module plugged in.
All JS-ICON ™ Series dimmer racks come with a removable EEPROM memory module
located on the MADD-24 board. The EEPROM memory module inserts into the
PORT1 connector located on the upper center of the board, and may be removed for
safe storage.
The EEPROM type is programmed for parameter (P) or firmware (F) operation. A
parameter EEPROM is used to backup all of the current configuration settings. A
firmware EEPROM is used to update the current firmware version running on the
MADD-24 microcontroller to the firmware version saved on the EEPROM.
The EEPROM memory module supplied with all JS-ICON ™ Series dimmer racks is
a parameter type with all of the factory default configuration settings saved onto it
before shipping.
MADD24-P Indicates the EEPROM memory module is for a MADD-24 microcontroller.
MADD24-P Indicates the EEPROM type is programmed for parameter (P) operation.
XXXXXX Press EXECUTE to display the silicone serial number parameter.
DISABLED Press EXECUTE and menu feature is disabled for factory use only.
MADD24-F Indicates the EEPROM type is programmed for firmware (F) operation.
VER X.X Press EXECUTE to display the version (VER) of the firmware.
DISABLED Press EXECUTE and menu feature is disabled for factory use only.
NONE! Indicates the EEPROM memory module is not installed.