Kasco GT-77 ATV Seeder - Manual (Page 3)

PARTS and ACCESSORIES FOR MODEL GT-77 BROADCASTER for A.T.V.’s
Shown in Drawing
When ordering parts, order by both part name and number ... not drawing number.
Drawing Part Number
Number Number Name of Part Needed
1. 500 Grey-Iron Base for GT-77............................................................... 1
3. & 4. 410A 1/2” x 1” Hexhead Capscrew w/Lock Washer................................ 2
8. 911 Hopper Complete with Screws & Decals ...................................... 1
9. & 11. 912 Lid w/Cotter Key ............................................................................ 1
10.,12.,13. 913 Lid Spring w/Screw, Washer & Nut .............................................. 1
14. 778 12-Volt Motor w/Whiz Nuts (#779) ................................................ 1
15. 501 Fan 4-Bladed (Plastic), 5/16” Shaft Hole, w/St. St. Setscrews .... 1
16. 502 1/4” x 3/8” Socket Screw, S.S. (Included with 501 Fan) ............... 2
17. 779 Whiz Nut (10-32) - Used on Motor ................................................ 2
19. 812 Complete Wiring Assembly ............................................................ 1
23. 794 Push-Pull Switch ............................................................................ 1
26. 541 Switch Bracket ............................................................................... 1
30. 107 1/4” x 1/2” Hex Head Cap Screw ................................................... 1
31. 512 Brace Rod - 5/16” Hole in End (Used on Carton “D” only) .......... 4
32.,33.,34. 407 5/16” x 1” Machine Bolt w/Nut and Lock Washer ........................ 2
35.,36.,37. 924 Brace Rod Clamp, Complete (Used on Carton “D” only) ............. 2
42. 781 Round Head Machine Screw, Left-Hand Thread - Used to
Bolt Bronze Bushing to Fan ..........................................................
1
43. 507 3/16” x 3/8” Round-head Machine Screw, St. St., w/Washer........ 1
44. & 45. 503 Bronze Agitator Bushing - Used on Fan & Pivot Plate ............... 2
46. 209 Vibrating Agitator - Stainless Steel .............................................. 1
47. 508L Nipple - Used on Agitator .............................................................. 1
48. *517 Blocking Plate - Optional (Must be purchased separately) ......... 1
49. 802S Pivot Plate - Stainless Steel .......................................................... 1
50. 510 3/16” x 3/8” Round-head Machine Screw, St. St. .......................... 4
51. 509 Guide Assemblies for Seed Gate (1 Set Consists of 2)
- Stainless Steel ..............................................................................
2 Sets
52. 504 Opening Plate w/Connecting Linkage - St. St.............................. 1
53. 803S Opening Gauge Control Plate w/515 Carriage Bolt, Wing Nut
and Washer - Works with Pivot Plate 802S - Stainless Steel .....
1
54.
56. & 57.
515 1/4” x 1/2” Carriage Bolt, St. St. - w/Wing Nut & Washer........... 1
58. & 59. 516 1/4” x 1/2” Hexhead Capscrew, St. St. - w/Washer ....................... 2
60. & 61. 505 1/4” x 1/2” Pan Head Bolt, St. St. - w/Locking Nut ...................... 1
62. 792 Control Handle ............................................................................... 1
63.,64.,65. 806A 3/16” x 1-3/4” Machine Screw, w/Nut & Washer........................... 1
66. 807 Compression Spring - Used on Handle Bolt ................................. 1
67. 831 “HERD Sure-Feed Broadcaster” Decal ......................................... 1
68. 210 Decal - Model GT-77 ....................................................................... 1
69. 1091 “WARNING” Spinning Blades Decal............................................. 1
70. 408A #10 x 3/4” Phillips Truss Head Machine Screw w/Nut ................ 4
511 Stand (Supplied with Mounting Carton D, JD-1 and U only) (Not Shown) 1
514B 1/2” x 1-3/4” Hexhead Capscrew, Lock Washer & Nut (Not Shown) 1
*Special blocking plates available for fire ant baits. Call factory for details.
1
MODEL GT-77 PARTS LIST 8/7/07 10:29 AM Page 3