Document Outline

• HarmonicGuard® Series Drive-Applied Harmonic Filter
• Installation, Operation, and Maintenance Manual
• TCI, LLC W132 N10611 Grant Drive Germantown, Wisconsin 53022
• Table of Contents
• Introduction
  • Safety Instructions Overview
  • Warnings and Cautions
    • Warnings
    • Cautions
  • General Safety Instructions
  • Receiving Inspection and Storage
    • Receiving Inspection
    • TCI Limited Warranty Policy
    • Storage Instructions
  • Pre-installation Planning
    • Verify the Application
      • HG7 Ratings
    • Select a Suitable Location
      • Environment
      • Working Space
    • Mounting an Open Panel Unit
    • Power Wiring
  • Installation Guidelines
    • Mounting
    • Wiring
      • Cable Entry Locations
      • Field Wiring Connection Terminals
      • Grounding
      • Power Wiring
  • HG7 Harmonic Filter Operation
    • Before Applying Power for the First Time
    • Operation
  • Installation
    • Intended Audience
    • Additional Information
    • Installation Checklist
  • Maintenance and Service
    • HG7 Harmonic Filter Reliability and Service Life
    • Periodic Maintenance
    • Troubleshooting
      • Reference Drawings
    • Fuse Specifications
      • Table 1a – Fuse Specifications for HG7 240 Volt Models
      • Table 1b – Fuse Specifications for HG7 380 – 415 Volt Models
      • Table 1c – Fuse Specifications for HG7 480 Volt Models
      • Table 1d – Fuse Specifications for HG7 600 Volt Models
    • Replacement Parts
    • Factory Contacts and Tech Support
  • Product Description
    • HG7 Drive-Applied Harmonic Filter
    • Nameplate Data
    • Figure 1 – Typical HG7 Harmonic Filter Nameplate
    • Part Number Encoding
    • Figure 2 – HG7 Part Number Encoding
    • Product Technical Specifications
    • Table 2 – HG7 ST and STC Option Harmonic Filter Technical Specifications
  • Drawings
    • Typical Schematic Diagrams and Outline and Mounting Dimension Drawings
      • Schematic Diagrams
      • Outline and Mounting Dimension Drawings
      • Additional Typical Drawings
• Standard Filter (ST)
  • HG7 Standard Harmonic Filter
• Contactor Option (STC)
  • STC Option Models
  • HG7 STC Option Harmonic Filter
• Power Monitor Package Option (XM)
  • HG7 “XM” Option Harmonic Filter
  • Product Technical Specifications
  • Table 3 – HG7 “XM” Option Harmonic Filter Technical Specifications
  • Control Wiring
    • Control Power
    • Filter Enable Input
    • Fault Alarm Relay
    • Figure 3 – Typical Connection Diagram
    • Control Wiring
  • HG7 “XM” Option Operation
    • Adjustments
      • Protection Monitor Settings
    • Start Up (Commissioning)
      • Before Applying Power for the First Time
      • Before Operating the Drive for the First Time
  • The HG2TM Protection Monitor
    • Introduction
      • Product Description
      • Figure 4 – HG2 Protection Monitor Display and Keypad
      • Display and Keypad
      • Table 4 – HG2 Protection Monitor Display and Keypad Features
    • General Operation
      • Power Up Sequence
      • Normal Operation
      • Changing the Displayed Parameter
      • Table 5 – Operating Parameter Display
      • Fault Detection
      • Table 6 – Fault Code Display
    • Setup Parameters
      • Introduction
      • Setup Procedure
      • Table 7 – Setup Menu
      • Changing the Security Code
    • Troubleshooting Units Equipped with the HG2TM Protection Monitor
      • Normal Operation
      • Protection Monitor Display and Status Lights
      • Protection Monitor Display Fault Codes
        • Table 8 – Fault Code Troubleshooting Procedures
    • Troubleshooting Units Equipped with Pilot Lights
      • Filter Enabled Pilot Light
      • Blown Fuse Indicating Pilot Lights
    • HG2 Protection Monitor Calibration
      • Introduction
      • HG2 Protection Monitor Calibration Procedure
    • Required Equipment
    • Measuring Voltages and Currents
    • Calibration Potentiometer Locations
    • Calibration Procedure
    • Troubleshooting Calibration Problems
    • Replacement Parts
    • Factory Contacts and Tech Support
• Kit Package Option (KP)
  • “KP” Option Models
  • HG7 KP Option Harmonic Filter
  • Product Technical Specifications
  • Table 9 – HG7 “KP” Option Harmonic Filter Components Technical Specifications
  • Table 10 – KPC Panelized Capacitors Technical Specifications
  • Installation
    • KLR/KDR Line Reactor Installation Instruction
    • Field Wiring Information
• Component Package Option (CP)
  • “CP” Option Models
  • HG7 CP Option Harmonic Filter
  • Product Technical Specifications
  • Table 11 – HG7 “CP” Option Harmonic Filter Components Technical Specifications
  • Installation
    • KLR/KDR Line Reactor Installation Instruction
    • Field Wiring Information