Vigo VG02006 - Manual (Page 3)

3
Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or
damage the finish and void the warranty.
MAINTENANCE
ASSEMBLY
REQUIRED TOOLS
Adjustable wrench
Allen key - supplied (to remove cartridge if needed)
Plumber's putty - optional
Pipe tape
Flat screwdrivers
SAFETY TIPS
If you use soldering for the installation of the faucet, the seats, cartridges and
washers will have to be removed before using flame. Damage caused by
improper soldering will void the warranty.
Protect your eyes with safety glasses when cutting or soldering water supply
lines.
IMPORTANT POINTS
Prior to beginning installation, turn off the cold and hot water lines and open the
hot and cold knobs on the old faucet to release pressure.
When installing your new faucet, turn the connector nuts finger-tight, then use
one wrench to anchor the fitting and a second wrench to tighten the nut.
Connections that are too tight will reduce the integrity of the system. and
potentially cause product failure which could lead to water damage.
Wrap all threaded connections with pipe tape available at your local hardware or
plumbing supply store. Always wrap in a clockwise direction.
Not all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT AND COLD WATER
SUPPLY LINES that are or will be connected to the new faucet to remove scale,
solder or their impurities which could damage the faucet and potentially void the
warranty.
1. SHUT OFF WATER SUPPLY.
REMOVE THE OLD FAUCET AND
FLEXIBLE HOSES. CLEAN SINK
SURFACE WITH A NON ABRASIVE
CLEANER IN PREPARATION FOR
THE NEW FAUCET.
2. REMOVE METAL NUT, RUBBER RING,
AND METAL RING FROM THE FAUCET.
ATTACH METAL BRAIDED HOSES TO
THE FAUCET.
3. POSITION THE FAUCET IN THE 1 3/8"
COUNTERTOP HOLE, FROM BENEATH THE
COUNTERTOP HOLE ASSEMBLE THE
PLASTIC HOLDER, RUBBER RING, AND
METAL RING IN THE ORDER DEPICTED IN
THE DIAGRAM. THEN THREAD METAL NUT
ONTO HOLLOW PIN. TIGHTEN THE METAL
NUT UNTIL FAUCET IS SECURE.
3
2
1
METAL NUT
4. IF SPRAY HOLDER IS NOT ATTACHED,
ATTACH THE SPRAY HOLDER AND
SPRAY HOSE TO THE FAUCET AND
TIGHTEN SCREW UNTIL SPRAY HOLDER
IS SECURE.
5. FEED SPRAY HOSE THROUGH SPIRAL NECK ENSURING THE FEMALE SPRAYER
CONNECTION IS POSITIONED TOWARD TOP OF SPIRAL NECK. ATTACH MALE SPRAYER
CONNECTION TO TOP OF FAUCET BODY WITH ADJUSTABLE WRENCH UNTIL TIGHT.
SEAT SPIRAL NECK INTO SPRAY HOLDER AND FIRMLY PRESS DOWN UNTIL SECURE.
6
7. ATTACH THE FEMALE
CONNECTIONS OF THE METAL
BRAIDED HOSES TO THE COLD
AND HOT WATER SUPPLY .
8. AFTER INSTALLATION IS COMPLETE, TURN ON THE WATER SUPPLY AND ALLOW BOTH
HOT AND COLD WATER TO RUN SEPARATELY FOR AT LEAST TWO MINUTE EACH. WHILE
WATER IS RUNNING, CHECK FOR LEAKS. IT IS IMPORTANT TO VIEW THE CONNECTIONS AT
THE MALE AND FEMALE FLEXIBLE HOSE CONNECTIONS. IF LEAKS ARE DETECTED, REFER
BACK TO THE INSTRUCTIONS AND ADJUST ACCORDINGLY. TIGHTENING NUTS SLIGHTLY
MAY STOP ANY MINOR LEAKS.
7
INSTALLATION
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact our Technical Support Department
before proceeding with installation.
6. ATTACH SPRAYER TO FEMALE CONNECTION OF SPRAYER
HOSE BY HAND AND TIGHTEN UNTIL SECURE.
ENSURE THAT PARTS ARE
ASSEMBLED IN THE ORDER AS
DEPICTED IN DIAGRAM TO PREVENT
DAMAGE TO FAUCET AND SUPPLY
LINES.
!
ENSURE THAT YOU USE PIPE TAPE
AND DO NOT OVER TIGHTEN THE
SUPPLY LINE NUTS AS THIS COULD
CAUSE PRODUCT FAILURE LEADING
TO WATER DAMAGE.
4
ENSURE THAT YOU USE PIPE TAPE
AND ADJUSTABLE WRENCH, DO NOT
OVER TIGHTEN AS THIS COULD
CAUSE PRODUCT FAILURE LEADING
TO WATER DAMAGE.
STABILIZES FAUCET
UNDER COUNTERTOP
VISUALLY INSPECT MALE AND FEMALE
SPRAYER HOSE CONNECTIONS AND
FAUCET BODY TO ENSURE THE WASHERS
AND FLOW RESTRICTORS ARE PRESENT.
MISSING OR DAMAGED WASHERS AND
FLOW RESTRICTORS COULD CAUSE
PERSONAL INJURY OR WATER DAMAGE.
!
!
!
SPRAYER
HOSE
CONNECTION
WASHER FLOW
RESTRICTER
SPRAY WASHER
PACKAGE CONTENT
FAUCET ASSEMBLY
NUT
PLASTIC
HOLDER
ALLEN
KEY
TWO
FLEXIBLE
HOSES
RUBBER
RING
METAL
RING WRENCH