Blizzard Lighting RokPix (Rev A) - Manual (Page 9)

Page 12
R
okPix Manual R
ev
. A
© 2013 Blizzard Lighting, LL
C
DMX Mode Allows the unit to be controlled by any universal DMX controller.
1.) The default mode for the
fi
xture is DMX, which appears as
d001
on the LED readout. T
o
select
a different DMX address, using the
<MENU>
button, select
Addr
,then hit
<ENTER>
. Use the
<UP/DOWN>
buttons to select the correct address, then hit
<ENTER>
to con
fi rm.
Setting the DMX Channel Mode: 1.) T
o
select a DMX channel mode, press the
<MENU>
button, then use the
<UP>
or
<DOWN>
buttons until the displa
y reads
Chnd
and press the
<MENU>
button. Then use the
<UP>
or
<DOWN>
buttons until the displa
y reaches y
our desired channel mode. Press the
<MENU>
button
to con
fi rm
.
Stand-Alone, Master/Slave, Sound Active Modes: Allows a single or Master/Slaved units to run factory installed programs at user selectable speeds.
1.) T
o
set the
fi
xture in Flash/F
ade mode, select
FLAS or FAdE
. T
o
con
fi
rm, press the
<EN-
TER>
button.
2.) Now
, y
ou can adjust the
fl
ash settings from
FL00-FL15
or the fade settings from
FA00-
FA15.
Then press the
<ENTER>
button to con
fi rm.
3.) T
o
use the
fi
xture in automatic mode, select
ASC-
, and press the
<ENTER>
button. Then use
the
<UP/DOWN>
to choose from
AS00-AS15
, then press the
<ENTER>
button to con
fi rm.
4.) Adjust the speed of the chase as abo
ve
using
SP15
(slowest) to
SP00
(fastest) then press the
<ENTER>
button to con
fi rm.
5.) T
o
set the
fi
xture as a sla
ve
unit, select
SLAU
, and hit
<ENTER>
. The unit will displa
y a
fl ash-
ing
SL.AU
to indicate it is in sla
ve
mode.
Sound Active Mode: 1.) T
o
use sound activ
e mode, select
SouA
, then press the
<ENTER>
button. Then use the
<UP/
DOWN>
buttons to choose
Sou1
or
Sou2.
Press the
<MENU>
button to con
fi rm
.
Standalone (Program) Mode: Allows a single unit to display a variety of colors and programs without a DMX controller.
1.) T
o
set the
fi
xture in manual mode, select
Pr--
. T
o con
fi
rm, press the
<ENTER>
button.
2.) Now
, select the progr
am by using the
<UP>
and
<DOWN>
buttons to select
Pr00-Pr21
. T
o
con
fi
rm, press the
<ENTER>
button.
Pr00-Pr12
are static colors. Adjust the chase speed by
using the
<UP>
and
<DOWN>
buttons to na
vigate to
SP-- ,
and press the
<ENTER>
button.
Then select from
SP00-SP15
(fast <--> slow).
Manual Color Adjustment: Allows the user to adjust the color balance of the
fi
xture. These settings are global, they will effect all modes.
1.) Use the
<MENU>
and
<UP/DOWN>
button to select
rL--
(R
ed Lev
el),
GL--
(Green Lev
el),
bL--
(Blue Lev
el) or
UL--
(White Lev
el), then hit
<ENTER>
.
2.) Using the <UP/DOWN> buttons, select the maximum lev
el for each color between
x000-
x255
(000=off
), then hit
<ENTER>
to con
fi rm.
Page 9
R
okPix Manual R
ev
. A
© 2013 Blizzard Lighting, LL
C
Fixture Linking (Master/Slave Mode)
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the
fi rst
fi xture.
2. Connect the end of the cable coming from the fi rst
fi
xture which will ha
ve
a (female) 3 pin connec
-
tor to the input connector of the next
fi xture
con-
sisting of a (male) 3 pin connector
. Then, proceed
to connect from the output as stated abo
ve
to the
input of the following
fi
xture and so on.
A quick note:
Often,
the setup for Master
-
Sla
ve
and Standalone
oper
ation requires that
the
fi rst
fi
xture in the
chain be initializ
ed for
this purpose via either settings in the control panel or DIP-switches. Secondarily
, the
fi xtures
that follow ma
y also re-
quire a sla
ve
setting.
Check the “
Operating Adjustments
” section in this manual for com-
plete instructions for this type of setup and con
fi gur
ation.
Mounting & Rigging This
fi
xture ma
y be mounted in an
y S
AFE position pro
vided there is
enough room for v
entilation.
It is important nev
er to obstruct the fan or v
ents pathw
ay
. Mount the
fi
xture using a suitable “C” or “O” type clamp
. The clamp should be
rated to hold at least 10x the
fi
xture’
s weight to ensure structur
al sta-
bility
. Do not mount to surfaces with unknown strength, and ensure
properly “r
ated” rigging is used when mounting
fi xutres
ov
erhead.
Adjust the angle of the
fi
xture by loosening both knobs and tilting the
fi xture.
After
fi
nding the desired position, retighten both knobs.
• When selecting installation location, tak
e into consider
ation lamp
replacement access (if applicable) and routine maintenance. • Safety cables MUST AL
W
A
YS be used.
• Nev
er mount in places where the
fi
xture will be exposed to r
ain,
high humidity
, extreme temper
ature changes or restricted v
entilation.