LaserLyte MBS-1 - Large Rez Size - Manual (Page 2)

5
6
25-30 Yards/Meters
Daylight
Laser Target
DAYLIGHT LASER TARGET
A. I .
II .
B. I.
II.
REMOVE BORE TOOL!
----------------------------------------------- or ---------------------------------------------
Laser Dot
Laser Dot
Sight
2 inch
(5cm)
.25
.50
.75
1.00
1.25
1.50
1.75
2.00
2.25
2.55
2.75
3.00
Target
10 Yards/Meters
.25 .50 .75 1.00 1.25 1.50 1.75 2.00 2.25
100 Yards
Mini Laser Bore Sight
MBS Sight-In Steps
MBS-1
UNLOAD YOUR FIREARM!
Find adapter to fit your barrel, thread proper screw into adapter.
Adjust adapter to fit snug inside of barrel.
Roll the switch until it comes on.
Sighting-in: A. 25-30 Yards/Meters - RECOMMENDED!
I. Shine laser dot out 25-30 Yards/Meters
II. Adjust cross hairs directly on top of the dot.
------------------------------- or -----------------------------------
B. 10 Yards/Meters (If 25-30 Yards/Meters not available)
I. Shine laser dot out 10 Yards/Meters
II. Using target adjust cross hairs approximately
2 inches/5cm above the red dot.
REMOVE BORE TOOL! At firing range fire first 100 yard/meter shot.
Make final adjustments.
1
2
3
4
5
6
1
2
3 4
.435 to .50 Cal.
.350 to .434 Cal.
.280 to .349 Cal.
.220 to .270 Cal.
UNLOAD
YOUR FIREARM!
UNLOAD FIREARM! Insert bore tool into the shotgun adapter and thread into screw.
Put into shotgun barrel.
Hold shotgun adapter and twist the bore sighter until a snug fit.
Once snug follow instructions for Sight-In steps.
1
2
3
1
2
3
4
Shotgun Adapter (Optional) MBS-PAK
Laser
line
Top View
Scope view
before
Scope view
after
Center
Bubble
3 Yards/Meters
1
3
5 6
2
4
1 2
WARRANTY:
Three year
limited warranty
DANGER
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
POWER OUTPUT < 5mw
WAVELENGTH 630-670mm
CLASS IIIa PRODUCT
20 Gauge
(.510 -.625 Caliber)
12 Gauge
(.625 -.750 Caliber)
Turn the laser to the on position.
Lift up on the plastic battery cup.
Pull out and replace batteries. Insert Batteries with positive (+) going into cup.
Put battery cup back into bore tool.
1
1 2 4
2
3
3
4
Battery Replacement: (3) 393 Batteries
UNLOAD FIREARM! Secure firearm in a rest and make level.
Follow 1-3 Sight-In Steps.
Put the adapter with ring over the end of the bore tool.
Adjust bubble between the two lines.
Turn on laser and shine on wall 3 yards/meters away.
Adjust cross hairs until they are parallel with red laser line.
Tighten down scope rings, pull off scope leveler and proceed
to Sight-In steps.
1
2
3
4
5
6
7
Gun Leveler
MBS-PAK
Scope Leveler Adapter
Slide gun leveler onto top scope rail.
Use the bubble level and adjust gun so bubble is between lines.
Secure gun, mount scope and follow scope leveling directions.
1
2
(Optional)
®
30 N. Alamos Drive - Cottonwood, AZ 86326
Phone 928-649-3201 - Fax 928-649-3970
www.LaserLyte.com
MBS_1.indd 3-4 8/10/12 6:48 AM