CLO Systems CLIKR-5 UR5L-8700L - Manual

Set-up Code Tables
6
SCIENTIFIC ATLANTA 001 003 041 042 045 046
PIONEER
001 103 034 051 063 076 105
PACE 001 005 002
SAMSUNG 001 030
MOTOROLA 002 111 148
DIGEO 153
GENERAL INSTRUMENT 005 103 104
HAMLIN
049 050 055
HITACHI 103 055
JERROLD 005 004 103 005 003 008 009 010 069
MAGNAVOX 010 012
MEMOREX 052
MOXI 111 252 153
NFUSION 192
PANASONIC 044 047
PHILIPS 006 012 013 020 085
PULSAR 052
RCA 047
REGAL 049 050
REGENCY 057
SKY 230 204
SONY 108
SPRUCER 047
TELNET 354
TOCOM 039 040 056
TOSHIBA 052
VIEWSTAR 012 015
ZENITH 052 060 093 100
A MARK 112 143
ABEX
025
ACCURIAN 036
ADMIRAL 072 251 333
ADVENT
247 388
ADVENTURA 002
AIKO 103
AKAI 116 146 248 404 405 473 475 323 387 391
ALBATRON 017
ALERON 028
AMERICA ACTION 043
AMPRO 073
AMSTRAD 052
ANAM 043 054 056 080 112
AOC
116 363 112 058
APEX 572
APEX DIGITAL 006
AQUAVISION 573 574
ASTAR 477
AUDIOVOX 076 454 388
AVENTURA 052
AVION 441
AXION 039
BELCOR 116
BELL&HOWELL 333 072
BENQ 423 600
BOXLIGHT 266
BRADFORD 043
BROCKWOOD 116
BROKSONIC 238
BYDESIGN 031 032
CANDLE 116 002 003 363
CAPEHART 058
CARY AUDIO DESIGN 266
CELEBRITY
001
CENTURION 116
CETRONIC 043
CHANGHONG
247
CITIZEN 116 002 003 363 043 258 103 143
CLARION 043
CLASSIC 043
CLP CLASSIC
333
COLORTYME 116
CONCERTO 363
CONCIERGE
073
CONTEC 043 050 051
CORNEA
116
CORONADO 143
CRAIG
043 054
CROSLEY 164
CROWN 043 143
CURTIS MATHES
116 258 363 143
CXC 043
CYBERHOME 015
DAEWOO 363 016 043 044 076 103 114 125 127 143
DAYTRON 363 143
DELL
320 164 363
DIGITAL PROJECTION 570
DIMENSIA
333
DREAMVISION 235
DUKANE 011 025
DUMONT 116 073
DURABRAND 096 052
DWIN 257
DYNASTY 043
DYNEX
400
EIKI 187
ELECTROBAND 001
ELECTROGRAPH 466
ELECTROHOME 143 024 076 196
ELEKTRA 072
ELEMENT 363 494 526
EMERSON 028 048 043 155 005 116 363 047 050 051
076 096 143 153 154 052 514
ENVISION 116
EPSON 324 590
ESA 323
FISHER 007 057
FUJITSU
246 198 410
FUNAI 028 043 052
FUTURETECH 043
GATEWAY
242 268
GE 073 116 008 009 034 056 074 155 333 363
GEM 391
GIBRALTER 116 073
GO VIDEO 026
GOLDSTAR 113 116 102 363 106 112 127 143
GRUNPY
028 043
HAIER 363 501
HALL MARK 363
HANNSPREE
349 381
HARLEY DAVIDSON 028
HARVARD
043
HAVERMY 081
HELLO KITTY 076
HIMITSU 043
HISENSE 419 442
HITACHI 011 166 009 010 012 023 075 143 158 072
363 250 587
HP 378 316 327 421
HUMAX 518
HYUNDAI 337 338
ILO 472 399
INFINITY 164
INFOCUS
333 230 547 548 470 532 564 595
INITIAL 035 282
INSIGNIA 350 400 052 164 403 454 457
INTEQ 073
JANEIL 002
JBL 164
JCB 001
JCPENNEY 024 116 008 009 030 065 258 143 333 363
JENSEN 013
JVC
038 034 001 083 199 210 533 581
KAWASHO 116 001
KEC 043
KENWOOD 116 001
KLEGG
466
KLOSS 002 059
KMC 143
KNOLL SYSTEMS 230
KONKA 457
KREISEN 530
KTV 043 116 143 154
KURAZAI 072
LG 363 113 116 102 106 112 127 143 569 284
LITEON 268
LODGENET 072
LOEWE
164
LOGIK 072
LUXMAN 363
LXI
166 007 138 052 251 333 164
MAGNAVOX 164 059 116 003 060 061 363 127 022 333
094 226 390 467 431
MAJESTIC 333 072
MARANTZ 116 164 281 562 584
MATSUI 164
MATSUSHITA
080
MAXENT 242
MEGATRON 116 011
MEMOREX 007 072 363
MGA
116 363 024 028 042
MIDLAND 333 073
MINTEK 362
MINUTZ 008
MISAKAI 052
MITSUBISHI 124 109 024 028 040 042 146 363 348 450
MONIVISION
017
MONTGOMERY WARD 333 072
MOTOROLA
081
MTC 116 363 258
MULTITECH 043
NAD 138 025
NEC 272 197134 116 040 016 024 056 019 262 236
281 575
NET TV 242
NIKEI 043
NIKKO 116
NIKO 527
NORCENT 390
NORWOOD MICRO 027
NTC
103
NUVISION 351 567
OLEVIA 432 363 333
ONKING 043
ONWA 043
OPTIMUS
025
OPTOMA 265 249
OPTONICA 019 251
ORION
096
PANASONIC 080 034 056 164 208 359 552 524
PHILCO 116 003 059 060 164 363 024 056
PHILIPS
164 005 093 038 116 003 363 059 127 206
431 333 161 594
PILOT 116
Manufacturer/Brand Set-Up Code Number
TV
Manufacturer/Brand Set-Up Code Number
CBL-CABLE Converters
Manufacturer/Brand Set-Up Code Number
TV
Manufacturer/Brand Set-Up Code Number
TV STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light will
turn on for 30 seconds indicating the
unit is ready to be programmed.
STEP3 Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
*Note : If the 3-digit code number you just
entered is correct, the Component will
turn Off. If it did not turn Off, continue
entering code numbers listed for that
brand until the Component turns Off.
STEP4 After you’ve entered the correct code
number and the Component has turned
Off, press the [POWER] button to turn the
Component back On. Now it is time to
test the VOLUME and MUTE buttons for
the TV (or PLAY and STOP buttons for
VCR and DVD) to make sure they all work.
If any of the functions do not work as they
should, repeat from STEP 3 using the next
3-digit code number listed for that brand
until you find the best Component code.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the same
[COMPONENT] button one more time.
The Component LED light will blink
twice to confirm that the code was
successfully stored.
Now, program the rest of your Components
by repeating STEPS 1-5.
*Note : If the Pre-Programmed Method did not
work, or if the Code Tables do not list
your Component brand, use the Auto-
Search Method as explained in Section B.
B. Auto-Search Method
STEP1 Turn on the Component you want to
program (TV, VCR, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) to be programmed
and [OK/SEL] button simultaneously for
3 seconds. The Component LED light
will turn on for 30 seconds indicating
the unit is ready to be programmed.
STEP3 Point the remote toward the Component
and press the [CH ] or [CH] button one
step at a time or keep it pressed. The
remote will emit a series of ON/OFF com-
mands. Release the [CH
] or [CH] but-
ton as soon as the Component turns Off.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any
of the functions do not work as they
should, repeat from STEP 3 using [CH
]
or [CH ] buttons to find the correct code.
STEP5 Save the code. (Same as for 3-Digit Code
Programming Method - Section A).
Now, repeat the Auto-Search Method for those
Components you could not program earlier
with the Pre-Programmed Method.If you can’t
find the right code using the Auto-Search
Method, try the Learning Method in Section C.
C. The Learning Method
STEP1 Press the [COMPONENT] button
(TV,VCR,DVD or AUX) to be pro-
grammed and the [ASPECT] buttons
simultaneously for 3 seconds until the
Component LED light turns on.
STEP2 Line up the CLIKR TM -5 to the other remote,
head-to-head, 1 or 2 inches apart.
STEP3 Press any button on the CLIKR TM -5 that
you want to teach a command to. For
example, if you want to teach the
[MUTE] button, press the [MUTE] but-
ton.
STEP4 Press and hold the [MUTE] button on
the other remote until the
CLIKR TM -5
Component LED light blinks twice.
*Note : The LED will blink 5 times if there
was an error in the learning
process. In so, repeat STEPS 3 and
4. Continue learning other buttons
by repeating STEPS 3 and 4.
STEP5 Once you have completed teaching
CLIKR TM -5 all desired commands for that
Component, save the learned commands
by pressing the [COMPONENT] and
[ASPECT] buttons simultaneously until
the Component LED blinks 3 times. Now
test all the buttons to make sure they
learned correctly.
D. Erasing a Single Learned Command
STEP1 Press the [COMPONENT] and [ASPECT]
buttons simultaneously for 3 seconds
until the Component LED light turns on.
STEP2 Press and hold the button you want to
erase for 3 seconds. The Component LED
will blink twice to confirm the erasure.
STEP3 To exit, press and hold both the [COM-
PONENT] and [ASPECT] buttons simul-
taneously until the Component LED
blinks 3 times.
E. Erasing All Learned Commands
from One Component
STEP1 Press the [COMPONENT] and [ASPECT]
buttons simultaneously for 3 seconds
until the Component LED light turns on.
STEP2 Press and hold both the [COMPONENT]
button you want to erase and the
[PAUSE] button for 5 seconds. The
Component LED will blink twice to con-
firm the erasure.
H. Programming the System On/Off Button
This allows you to program the System On/Off
button so it can send up to five power On/Off
commands with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM ON/OFF] button and
the [OK/SEL] button simultaneously for 3
seconds. The [CBL] button will turn on for
30 seconds.
STEP3 Press the first [COMPONENT] button you want
to store in the [SYSTEM ON/OFF] button and
then the [POWER] button. Repeat this for other
Components until you have stored all the
desired power commands into the [SYSTEM
ON/OFF] button.
STEP4 Press the [CH] button to save the
power commands you stored. The [CBL]
button will blink twice to confirm the
commands have been saved.
I. Programming Channel Control
You can program the channel controls (Channel
Up, Channel Down, Last and Numbers) from one
Component to operate in another Component
mode. Default channel control settings on the
remote control are as follows:
CBL : CBL T V : CBL VCR : CBL
DVD : DVD AUX : AUX
If you wish to store the TV channel control in TV
mode, use the following steps.
STEP1 Press the [TV] button and the [OK/SEL]
button simultaneously for 3 seconds.
The [TV] Component LED will turn on for
30 seconds.
STEP2 Press the [VOL] button.
STEP3 Press the [TV] button again.
The Component LED will blink twice to
confirm the programming.
To return to original state:
If you wish to restore the CABLE channel con-
trol in TV mode, repeat the above steps but
press [CBL] in STEP3 .
J. Programming Volume Control
Volume and Mute control are factory-programmed to
automatically transfer to the respective Component
mode you select, as follows:
CBL : CBL T V : TV VCR : TV
DVD : TV AUX : AUX
However, you can program the volume controls
(Volume Up, Volume Down and Mute) from one
Component to operate in another Component.
If you wish to store the TV volume control in CBL
mode, use the following steps.
STEP1 Press the [CBL] button and the [OK/SEL] but-
ton simultaneously for 3 seconds. The [CBL]
Component LED will turn on for 30 seconds.
STEP2 Press the [VOL] button.
STEP3 Press the [TV] button.
The Component LED will blink twice to
confirm the programming.
To return to original state:
If you wish to restore the CBL volume control in CBL
mode, repeat the above steps but press [CBL] in STEP3 .
K. Programming a ‘Macro’ button.
If your remote model has custom-programmable Macro
buttons available, they can be programmed to act as a
'Macro' or Favorite Channel button in CABLE mode. This
allows you to program up to five 2-digit channels, four 3-
digit channels or three 4-digit channels that can be
accessed with one button press.
STEP1 Press the [CBL] button to select the CBL mode.
STEP2 Press the [MACRO] button and [OK/SEL]
button simultaneously for 3 seconds. The
[CBL] button will turn on for 30 seconds.
STEP3 Enter the the 2, 3 or 4-digit code for the channel
you want programmed first (for example, 007)
using the Number Pad, then press the [STOP]
button. Then enter the code for the next chan-
nel (for example, 050), then press the [STOP]
button. Repeat this process for the third chan-
nel. The [CBL] button will blink once for each
channel entered.
STEP4 Press the [CH] button to store the channels
that were selected. The [CBL] button will blink
twice to confirm the storage of commands.
To access the programmed channels, press the
[MACRO] button once. This will bring up the
first channel. Press once again and it will bring
up the second channel. Press again and it will
bring up the third channel.
L. Low Battery Warning
When the batteries are low and need to be replaced
with fresh batteries, the Component LED lights will
blink 2 times in sequence whenever a [POWER] but-
ton is pressed to turn on equipment.
M. Memory Lock System
This remote control is designed to retain pro-
grammed memory for 10 years even after batteries
are removed from the remote control.
N. Record Your Component Set-up Codes
TV Set-up Code Number:
VCR Set-up Code Number:
DVD Set-up Code Number:
AUX Set-up Code Number:
For additional information about your remote
control, go to www.universalremote.com
STEP3 To exit, press and hold both the [COMPONENT]
and [ASPECT] buttons simultaneously until the
Component LED blinks 3 times.
F. Finding a Component Button’s
Setup Code Number
If you used either the Auto-Search or Learning
Methods to program a Component, you may not
know what the correct code number is. Here is a
way for you to identify the code number, so you
can record it for future reference.
STEP1 Press the [COMPONENT] button (TV,
VCR, DVD or AUX) you want to verify and
the [OK/SEL] button simultaneously for 3
seconds. The Component LED light will
turn on for 30 seconds.
STEP2 Press the [INFO] button and count the num-
ber of times the Component LED light blinks.
This number indicates the first digit of the
code, followed by the second and third,
each separated by a one second pause
when the LED will turn off.
*Note : 10 blinks represents the number zero.
Example : One blink, (pause), eight blinks,
(pause) and three blinks, indicates
code number 183.
G. AUX Function: Programming a 5 th
Component
You can take advantage of the AUX function to
program a 5
th Component such as a second TV,
VCR, DVD or Audio Component.
STEP1 Turn on the 5 th Component you want to
program (TV, VCR, DVD or Audio).
STEP2 Press the [AUX] button and the
[OK/SEL] button simultaneously for 3
seconds.The [AUX] Component LED will
turn on for 30 seconds.
STEP3 Press the [COMPONENT] button you
want to setup. Point the remote control
toward the Component and enter the 3-
digit code number assigned to your
brand.
*Note : If the 3-digit code number you just
entered is the correct number, the
Component will turn Off. If it did not
turn Off, continue entering code num-
bers listed for that brand until the
Component turns Off.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section A). If any
of the functions do not work as they should,
you need to find a new code.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the [AUX] button
one more time. The Component LED light
will blink twice to confirm the code was
stored. Now when you press the AUX
button, all the buttons will work with that
5
th Component.
Button Functions
4
There are two ways you can program your CLIKR TM -5 remote:
* The Pre-Programmed 3-Digit Code Method
* The Auto-Search Method
* The Learning Method
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit
code numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest
and easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The
Auto-Search Method scans through all the codes in the remote control, one at a time. The
Learning Method allows you to transfer functions from other remotes, one button at a time.
IMPORTANT SETUP NOTE!
This pertains to all programming steps. When you are in setup mode, a component LED will light
for 30 seconds.If you do not press a button within 30 seconds, the LED light will turn off and exit
setup mode and you will need to start over.
A. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to program (TV, VCR, DVD or AUX).
Universal Remote Control, Inc.
www.universalremote.com
OCE-0060E REV 07 (02/26/10)
UR5L-8700L & UR5L-8720L
Operating Instructions For
CLIKR ™ -5
Cable Remote Control
The CLIKR TM -5 UR5L-8700L & UR5L-8720L
are designed to operate the Scientific-
Atlanta, Pioneer, Pace Micro, Samsung and
Motorola digital set tops, plus the majority
of TV, VCR, DVD and AUDIO equipment on
the market as shown below.
CABLE : Cable Converters TV : Televisions
VCR : VCRs and TV/VCRs DVD: DVD Players
AUX : Audio Receivers and DVRs, etc.
Introduction
1
DEFAULT STATE:
Component Default: CABLE Set Top Box (STB)
Channel Default: CABLE channel and numbers
through the CABLE STB. You have the option of
controlling your CABLE channel and numbers
through the TV or VCR. Refer to section I for
programming steps.
Volume Default: Volume and Mute control are
automatically transferred to the respective
Component mode you select, as follows: CBL:
Cable Set Top Box / TV: TV / AUX: AUX. Volume
and Mute control for VCR and DVD are auto-
matically transferred to the TV. However, you
have the option of controlling CABLE Volume
and Mute through the TV, VCR or AUX. Refer to
section J for programming steps.
Operations
3
Replacing Batteries
2
Before you program or operate the remote
control, you must install two new AA alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
Programming the Remote Control
5