Xp 63 led light – SoundOff Signal XP 63 Deck/Grille Light User Manual
Page 2
EL6GD(x) 4.09
Predator Sync Confi guration Instructions
IMPORTANT! A MAXIMUM OF 4 SINGLE LIGHTS
CAN BE SYNCED TOGETHER
1. Set ID#
a. Identify which pattern and sequence you want and look up ID#
settings at right.
b.
Connections
i. RED:
+12Vdc
ii. WHT: +12Vdc (Note: you will need to disconnect after power is
applied)
iii.
BLK:
Ground
c. Apply power to unit
d. Without disconnecting power from unit, disconnect WHT wire
e. Momentarily connect WHT to Ground to change ID #
i. Identify ID# by number of sequential fl ashes
ii. Possible ID#s: 1 – 4
f. Disconnect power from unit to get out of ID mode.
2. Set Pattern
a. Reapply power to units.
b. Once all Light Head ID#s are confi gured, make sure all lights are
fl ashing the same pattern
c. Connect corresponding colored wires of all units together: RED to RED,
etc.
d.
Change
Pattern
i. Momentarily connect WHT wires to Ground
ii. Observe pattern change on all lights
connected
e. Insulate all wires by taping with electrical tape
3. Connect Master Switch for Application
a. IMPORTANT! Ensure WHT Pattern/Sync Wires
are tied together
NOTE: The light CANNOT be serviced in the fi eld. Any attempt to
gain access to the unit will most likely cause permanent damage
and void its warranty.
1 Quint
ALT
ID#1
ID#3
ID#1
ID#1
-
-
-
-
2 Warp
ALT
ID#1
ID#3
ID#1
ID#1
-
-
-
-
3 Inter-Cycle Flash
ALT
ID#1
ID#3
ID#1
ID#1
-
-
-
-
4 Double
ALT
ID#1
ID#3
ID#1
ID#1
-
-
-
-
5 Quad Flash
ALT
ID#1
ID#3
ID#1
ID#1
-
-
-
-
6 3FPS
ALT
ID#1
ID#3
ID#1
ID#1
-
-
-
-
7 3FPS
SIM
ID#1
ID#3
ID#1
ID#1
-
-
-
-
8 Q-SWITCH
VARIABLE
ID#1
ID#3
N/A
N/A
-
-
-
-
9 WARP, STEADY BURN
STEADY BURN
ID#1
ID#3
N/A
N/A
-
-
-
-
10 QUAD, STEADY BURN
STEADY BURN
ID#1
ID#3
N/A
N/A
-
-
-
-
11 E-PATTERN SINGLE FLASH
ALT
ID#1
ID#3
ID#1
ID#1
-
-
-
-
12 E-PATTERN DOUBLE FLASH
ALT
ID#1
ID#3
ID#1
ID#1
-
-
-
-
13 E-PATTERN SINGLE FLASH
SIM
ID#1
ID#3
ID#1
ID#1
-
-
-
-
14 E-PATTERN DOUBLE FLASH
SIM
ID#1
ID#3
ID#1
ID#1
-
-
-
-
15 X-WARP
X
N/A
N/A
N/A
N/A
ID#1
ID#1
ID#1
ID#1
16 X-DOUBLE
X
N/A
N/A
N/A
N/A
ID#1
ID#1
ID#1
ID#1
ALTERNATING (ID#s
DIFFERENT FOR
EACH LIGHT HEAD)
SIMULTANEOUS
(ID#s DIFFERENT
FOR EACH LIGHT
HEAD)
X-PATTERN (PATTERN 15 AND 16 ONLY)
LIGHT HEAD ID# TABLE
# PATTERN
SEQUENCE
LT HD1
LT HD2
LT HD1
LT HD2
LT HD1
LT HD2
LT HD3
LT HD4
1 LIGHT
Single Light Operation: Follow the ID Selection steps and set the LED3 to
ID#1 if it is not already. NOTE: Steady Burn is produced for patterns 9 &
10 in Single Operation.
2 LIGHTS
ALTERNATING: To obtain Alternating patterns, follow the ID SELECTION
steps and set one LED3 to ID#1 and the other to ID#3. Then proceed to
the PATTERN SELECTION steps.
SIMULTANEOUS: To obtain Simultaneous patterns, follow the ID
SELECTION steps and set both LED3 lights to ID#1. Then proceed to
PATTERN SELECTION steps.
4 LIGHTS
X-Pattern: To obtain X-patterns, follow the ID SELECTION steps and set
one of the four LED3 lights to ID#1, one to ID#2, one to ID#3, and one
to ID#4. Then proceed to PATTERN SELECTION steps. NOTE: Be sure to
mount each LED3 in the correct placement based on ID#.
X-Pattern Light Head Placement
ID#4 ID#2
ID#3
ID#1
X-Pattern Sequence
ID#1 > ID#4 > ID#2 > ID#3
WIRE HOOK-UP TABLE
WIRE COLOR:
CONNECT TO:
RED
+9-16Vdc
BLACK
Ground (-)
WHITE
ID/Pattern Select
XP 63 LED LIGHT
EL6GD(x)
TECHNICAL SPECIFICATIONS
Overall Dimensions:
3.38”(2.88”min)”H x 5.13 W
x 2.63”D
Flash Patterns:
16 fl ash patterns
Input Voltage Range:
10 - 16 Vdc
Current Consumption:
<1 amp*
# of LEDs:
6 Generation 3 LEDs
Light Sync Technology:
Yes
Operating Temperature:
-40º to +65º C
*Pattern Dependent