SWIT Electronics S-8172S - Manual

8KINGXMKGHRK2OOUT(GZZKX_6GIQ
9  '99  '9
¡ ¢ £ ¤ ¥ ¦ ¥ ¦ ¦ ¦
USER MANUAL
S W I T E l e c t r o n i c s C o . , LT D.
Tel: +86-25-85805753
Fax: +86-25-85805296
http://www.swit.cc
E-mail: [email protected]
)NGXGIZKXOYZOIY
1. High performance Li-ion battery pack, rechargeable.
2. Large capacity with separable design, not restricted by IATA air
transportation regulations.
3. 4-step LED power indicator.
4. D-tap DC output and charging socket.
5. Build-in multiple protective circuits.
1. The battery pack is disassembled in package. Please assemble the
part A and part B first, and make sure the serial numbers of the 2
parts are the same.
2. The battery pack should be disassembled and packed individually
before boarding to airplane. (Each part has under 100Wh capacity
and will not be restricted by IATA regulations.)
3. The battery pack can not be used or charged until the part A and
part B are assembled.
4. Please mind the polarity of the D-tap socket when using DC output.
5. Do not expose the battery pack to rain or moisture environment.
6. Do not expose the battery pack to temperature above 60°C.
7. Keep the battery pack terminals clean.
8. The battery pack may become warm in use or while being charged.
This is normal.
2+*OTJOIGZUX
1. The four-step LEDs indicate the remaining capacity when press
the “CHECK” button.
2. The indicator may not be accurate when the battery is powering
on the camera.
3. When only one LED indicates, please charge the battery as soon
as possible.
Disassembly: (When air transportation)
1. Set the lock of Part A to “UNLOCK”.
2. Slip the Part A out of Part B.
3. Keep the 2 parts separately during air transportation.
9ZUXGMK
Please disassemble the battery and keep the 2 parts separately in
cool, dry and clean place.
Model
S-8172A
S-8172S
S-8192A
S-8192S
Mount type
Gold mount
V-mount
Gold mount
V-mount
Nominal voltage
14.4V
14.4V
14.4V
14.4V
Capacity
158Wh
158Wh
184Wh
184Wh 11.1Ah
11.1Ah
12.8Ah
12.8Ah
Max output
100W
100W
100W
100W 8A
8A
8A
8A
Dimension
168Ч101Ч65mm
168Ч101Ч60mm
168Ч101Ч65mm
168Ч101Ч60mm
Mass
1.25Kg
1.25Kg
1.27Kg
1.27Kg
9VKIOLOIGZOUTY
)NGXMOTM
1. The battery pack is not fully charged when it is purchased.
Charge the battery before use.
2. Use SWIT charger or the chargers recommended by SWIT.
3. Do not use the D-tap socket while charging.
4. The battery pack should be charged within a temperature range
of 0-40°C.
1. Fully charged battery pack will discharge naturally and please
use it as soon as it gets charged.
2. At low temperature, the running time of battery pack usually
decreases.
3. The internal impedance of battery pack will be greater at low
temperature, which may cause the automatically circuit cutting.
4. The battery pack will cut off power automatically when overload
or any abnormal detected. Please take off the battery from
equipment, lay it for a while and charge on any of SWIT chargers,
and it will be re- activated and get charging normally.
)G[ZOUT
*OYINGXMOTM
*)YUIQKZ
The D-tap DC socket can be used as 14.4V DC output or SWIT
S-3010B charging input.
1. Open the rubber cover and plug in D-tap lead to DC output or
charge. (Mind the polarity of the D-tap plug)
2. Close the rubber cover when disconnected, to keep the socket
away from dust.
'YYKSHR_GTJ*OYGYYKSHR_
Assembly: (When using)
1. Set the switcher of Part A to “UNLOCK”.
2. Slip the Part A into Part B that with the same SN. It will beep
twice to confirm the match. If the battery beeps constantly when
assembled, please check the serial numbers of part A and B.
3. Set the switcher of Part A to “LOCK” and finish.
LOCK
UNLOCK
IMPORTANT SAFETY INSTRUCTIONS
Never short-circuit the battery pack terminals.
Never attempt to open the battery pack.
Keep the battery pack away from fire.
Avoid strong mechanical shock.