BMW M6 Coupe 2006 - Manual (Page 189)

M
o
bi
lity
187
Re
fe
re
n
c
e
At
a
g
la
n
c
e
Co
n
tr
o
ls
D
riv
in
g ti
ps
C
o
m
m
uni
ca
ti
o
n
s
Na
v
iga
ti
on
En
te
rt
a
in
m
e
n
t
8. With the ignition switched on, refer to
page
50 :
Switch on the device and allow to run for
approx. 3 minutes to fill wheel with sealant.
It is not important what inflation pressure
the tire has after filling.
9. Switch off device.
10. Remove connecting hose from connection
of sealant bottle and tire valve.
Stow the M Mobility System in the vehicle
again.
Distributing sealant
Immediately drive approx. 2 miles/3 km so that
sealant is evenly distributed in tire.
Do not exceed a maximum speed of
35 mph/60 km/h. Do not drop below
12 mph/20 km/h if possible. <
Producing tire inflation pressure
1. After approx. 2 miles/3 km, stop at suitable
location.
2. Screw compressor hose 9 directly onto tire
valve.
3. Insert connector 3 in lighter socket in vehi-
cle interior.
4. Correct tire inflation pressure to 29 psi/
200 kPa. With the ignition switched on:
> Increase inflation pressure: switch on
device, position I. To check currently set
inflation pressure, briefly switch off
device.
Do not allow compressor to run
longer than 10 minutes, otherwise
the device will overheat and may be dam-
aged.
<
> Reduce inflation pressure: press but-
ton
8 or turn screw 8 on pressure gauge.
If the inflation pressure is not held, drive
the vehicle again, refer to Distributing
sealant. Then repeat steps 1 to 4 once.
Using the M Mobility System can be ineffective
with tire damage from a size of approx. 0.16 in/
4 mm. Please contact the nearest BMW center,
refer to page
192 , or a workshop that works
according to BMW repair procedures with cor-
respondingly trained personnel if the tire can-
not be made ready for driving with the
M Mobility System.
<
The tire inflation pressure must be at least
29 psi/200 kPa. Otherwise do not con-
tinue driving. <
Continue driving
Do not exceed the permissible maximum
speed of 50 mph/80 km/h, otherwise
accidents can occur. <
Reinitialize the Flat Tire Monitor.
For details, refer to page
74 .
Have the defective tire and the sealant bottle of
the M Mobility System replaced as soon as
possible.
<
Changing wheels
Safety precautions in the event of a flat
tire or wheel change: park the vehicle as
far as possible from passing traffic and on solid
ground. Switch on the hazard warning flashers.
Lock the steering wheel in straight-ahead set-
ting of the wheels. Set the handbrake and
engage a driving position with the selector
lever.
Have all vehicle occupants get out of the vehicle
and ensure that they remain outside the imme-
diate area in a safe place, such as behind a
guardrail.
If a warning triangle or portable hazard warning
lamp is required, set it up on the roadside at an
appropriate distance from the rear of the vehi-
cle. Comply with all safety guidelines and regu-
lations.
Change the wheel only on a level, firm surface
which is not slippery. The vehicle or the jack
could slip to the side if you attempt to raise the
vehicle on a soft or slippery surface such as
snow, ice, tiles, etc.
Position the jack on a firm support surface.
Do not use a wooden block or similar object as a
support base for the jack, as this would prevent
it from extending to its full support height and
reduce its load-carrying capacity.
Online Edition for Part No. 01 41 0 012 118 - © 02/06 BMW AG