Canon BJC 7100 - Manual (Page 11)

Page
3 -18
Figure 3 -19 Hidden Control Sheet (Sample)
3 -20 Figure 3 -20 Nozzle Check Pattern (Sample)
3 -22 Figure 3 -21 Service Mode Test Print (Sample)
3 -23 Figure 3 -22 EEPROM Data Print (Sample)
Part 4: TECHNICAL REFERENCE
4 - 1 Figure 4 - 1 Printer Block Diagram
4 - 2 Figure 4 - 2 Flowchart of Initialization Sequence
4 - 3 Figure 4 - 3 Print Signal Sequence
4 - 5 Figure 4 - 4 Power-Off Sequence Flowchart
4 - 6 Figure 4 - 5 Bidirectional Centronics Specifications Selection Sequence
4 - 6 Figure 4 - 6 Interface Timing (Compatible Mode)
4 - 7 Figure 4 - 7 Interface Timing (Nibble Mode)
4 - 7 Figure 4 - 8 Interface Timing (ECP Mode)
4 - 9 Figure 4 - 9 Photo Print Mode (Image)
4 -10 Figure 4 -10 Print Mode Main Sheet (Sample)
4 -11 Figure 4 -11 Print Mode Detail Quality Sheet (Sample)
4 -13 Figure 4 -12 Printer's Mechanical System
4 -15 Figure 4 -13 Structure of BC-60
4 -16 Figure 4 -14 Structure of BC-61
4 -17 Figure 4 -15 Structure of BC-62e Photo
4 -19 Figure 4 -16 Structure of BC-60 BJ Head Unit
4 -19 Figure 4 -17 Structure of BC-61 BJ Head Unit
4 -20 Figure 4 -18 Structure of BC-62e Photo BJ Head Unit
4 -21 Figure 4 -19 Nozzle Arrays
4 -22 Figure 4 -20 Signal Contacts
4 -24 Figure 4 -21 Block Diagram of BC-60 Drive Circuit
4 -25 Figure 4 -22 Block Diagram of BC-61/BC-62e Photo Drive Circuit
4 -32 Figure 4 -23 Purge Unit
4 -33 Figure 4 -24 Carriage
4 -35 Figure 4 -25 Paper Feed Motor Drive Switching
4 -36 Figure 4 -26 Auto Platen-Head Gap Adjustment
4 -37 Figure 4 -27 Paper Feed Mechanism
4 -38 Figure 4 -28 Paper Separator
4 -39 Figure 4 -29 Printer Electrical System
4 -40 Figure 4 -30 Logic Board Block Diagram
4 -43 Figure 4 -31 Printer Block Diagram
4 -44 Figure 4 -32 Motor Drive Circuit
4 -45 Figure 4 -33 AC Adaptor Output Voltages
4 -46 Figure 4 -34 Sensor Positions
Part 5: MAINTENANCE
5 - 3 Figure 5 - 1 Grease Points
5 - 4 Figure 5 - 2 Main Cover and Connector Cover
5 - 4 Figure 5 - 3 Releasing the Carriage Lock
5 - 5 Figure 5 - 4 Bearings at Ends of Support shaft
5 - 5 Figure 5 - 5 Purge Unit and Bottom Case Assembly
5 - 5 Figure 5 - 6 Tightening Idler Pulley Assembly Screw
5 - 6 Figure 5 - 7 Maintenance Jet and Waste Ink Absorbers
5 - 7 Figure 5 - 8 Tightening the Chassis Fixing Screws
5 - 8 Figure 5 - 9 Screws Influencing Head Gap
5 - 9 Figure 5 -10 Measuring Sheet Setting 1
5 - 9 Figure 5 -11 Measuring Sheet Setting 2
VII