LaserMax LMS-UNI-MAX GREEN User Manual

Installation guide, Installing the laser system changing the batteries, Accessories

Advertising
background image

For: UNI–RED, UNI–GREEN, and UNI–IR

Installing the Laser System

Changing the Batteries

Installation Guide

What’s in the Box

A

Laser Housing

B

Battery Cover

C

Clamping Screw

D

Phillips Head Screws

E

Batteries 357 (2) or 1/3N (2)

F

Adjustment Tool

G

Activation Switch

1 | Remove the magazine from your

firearm and clear the chamber.

Check if your gun is unloaded.

2 | Check again!

3 | Slightly loosen the clamping

screw on the laser housing

to open the rail grips.

DO NOT REMOVE CLAMPING

SCREW. Mount the laser on the

rail of your firearm, making sure

the rail grips on the laser unit are

firmly set into the grooves on the

rail and the clamping screw is in

line with the notch in your rail

(figure A).

4 | Tighten the clamping screw with

the fingers to ensure a secure

fit (figure B). Further tighten the

clamping screw with a

screwdriver or coin until the laser

is firmly attached (figure C).

5 | Turn on the laser by pressing in

on the activation switch from the

right or left side. The center

position is off.

6 | Follow the manufacturer’s

instructions to attach your choice

of additional accessories onto

the Integrated Picatinny Rail

(figure D).

1 | Unscrew and remove

both phillips head screws from

battery cover.

2 | Remove battery cover from laser

housing and insert batteries into

unit as shown.

3 | Put battery cover back in place

on laser housing, making sure

the lip on the cover first engages

the slot in the laser housing.

4 | Install and tighten both Phillips

head screws into battery cover.

Do not overtighten.

TIMEOUT!
To avoid unintentional

battery drain, the laser is set

to automatically turn off after

10 minutes. When timed out,

simply cycle the activation
switch to refresh the laser and
turn it back on!

Spare Parts List

LMS–UNI–RG

Removable rail grip

LMS–UNI–CS

Clamping screw

LMS–UNI–AS

Activation switch

LMS–2X357 or LMS–2X13N

Batteries: 357 (2) or 1/3N (2)

LMS–AT50

Adjustment tool

A

C

G

F

E

D

B

Accessories

LMS–UNI–MAS–6

Momentary Activation Switch 6” cord

LMS–UNI–MAS–10

Momentary Activation Switch 10” cord

LMS–ADP–SIGMA

Rail adapter for S&W Sigma series

LMS–ADP–SHOTGUN

Rail adapter for 1” shotgun mag tube

LMS–HKADP–C

Rail adapter for H&K USP compact

LMS–HKADP–F

Rail adapter for H&K USP full size

LMS–ADP–AR

Rail adapter for Black Rifles

A

B

C

D

E

F

Changing the Laser Mode

Turn the laser on for at least two seconds, then turn it off. Next,

turn the laser on and off three times from the same side while
stopping at the center position while turning off (each on/off cycle
should take less than half of a second).When the laser is turned on,
the mode will have changed. To return the laser to the previous
mode, repeat the process.

01785-0-51

Disclaimer

Export of LaserMax IR Lasers is strictly prohibited without a valid export license

issued by the U.S. Department of State Office of Defense Trade Controls, in

accordance with International Traffic in Arms (ITAR), Title 22, Code of Federal

Regulations Part 120-130. Transfer to a foreign person is considered

an export even if done within the US. For further information contact

the Office of Defense Trade Control @ (202) 663-1282

.

Advertising
This manual is related to the following products: