Clarion WXZ466MP - Manual (Page 10)

10
WXZ466MP
280-8171-00
English 6. OPERATIONS
Basic Operations
Note:Be sure to read this chapter referring to the front diagrams of
chapter “3. CONTROLS” on page 5 (unfold).
Be sure to lower the volume before switch-
ing off the unit power or the ignition key. The
unit remembers its last volume setting. If
you switch the power off with the volume up,
when you switch the power back on, the
sudden loud volume may hurt your hearing
and damage the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [SOURCE] knob.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3. Press and hold the [SOURCE] knob for 1 sec-
ond or longer to turn off the power for the unit.
Note:
• Disk check
This unit will check the discs inside it when you
turn on the power for the first time after wiring or
when you press the reset button.
• System check
During the initial power up of this unit, it will go
through a system check procedure. This proce-
dure verifies any devices connected through
CeNET. Any additional CeNET devices plugged
into the unit after the initial power up will initiate
the system check procedure. When the power is
turned on, “SYS CHECK” appears in the display
if the wire connections were modified. The system
check starts automatically within the unit.
Selecting a mode
1. Turn the [SOURCE] knob to change the op-
eration mode.
2. Each time you turn the [SOURCE] knob, the
operation mode changes in the following or-
der:
Radio mode CD/MP3 mode CD
changer mode DVD changer mode
TV mode AUX mode Radio mode...
∗ External equipment not connected through
CeNET will not be displayed.
Adjusting the volume
1. Turn the [VOLUME] knob to adjust the vol-
ume.
∗ The volume level is from 0 (minimum) to 33
(maximum).
Switching the display
●When the power is turned on
1. Each time you press the [DISP] button, the
display switches in the following order:
●Radio mode
Main display (frequency) ➜ Title display
➜ Clock display ...
●CD/MP3 mode
Folder/Track No. display (MP3/WMA disc
only)
➜ Main display (Play time) ➜ Title
display ➜ Clock display ...
∗ Once selected, the preferred display becomes
the display default. When a function adjust-
ment such as volume is made, the screen will
momentarily switch to that function’s display,
then revert back to the preferred display sev-
eral seconds after the adjustment.
∗ When you have entered a title in a CD/MP3/
WMA, it appears in the display. If you have not
entered a title, “NO TITLE” appears in the dis-
play. For information on how to enter a title,
refer to the subsection “Entering titles” in the
section “Common Operations”.
●When the power is turned off
1. Each time you press the [DISP] button, the
display switches in the following order:
Clock display ➜ Display off ➜ Clock dis-
play...
●When the display is turned on
1. Press the [SPE/ANA] button for 1 second or
longer to turn off the display.
To turn on the display, press the [SPE/ANA]
button again or press the [DISP] button.
∗ The following buttons are valid while the dis-
play is turned off.
[SOURCE] / [VOLUME] / [ISR] / [LOAD] /
[
Q]
CAUTION
+WXZ466MP-009-ENG 05.9.13, 10:50 10