Notes, Setting the code, Step 1: entering the code number – Sony RM-V701 User Manual
Page 2: Note, Step 2: checking if the code number works, If the commander doesn't seem to be working, Searching for the correct code, Changing the component type of the positions
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Do not attempt to change the position of the switch after you have
sot it. Doing so may erase the preset component code numlx'r stored
in the memory of the Commander.
Charging the internal rechargeable battery with the
Solar Cells
This Commander is equipped with a solar cell that charges the
internal rechargeable battery if you keep the Commander in a well-
lighted place such as by a window.
Therefore, you will not need to replace the battery.
Notes
• Be sure to keep the Commander with the front facing upward and
in a well-lighted place. If you keep the Commander placed upside
down or in a dark place for an extended period of tinrv%;the internal
rechargeable battery will not be charged. If you continue using it
without charging, the rechargeable battery will be completely
discharged.
• When the rechargeable battery becomes discharged, the operating
range of the Commander becomes narrower. Be sure to charge the
battery periodically by placing the Commander in a place such as
by a window that lets in sufficient light.
• Do not place the Commander in a place subject to direct sunlight.
Setting the Code
Follow the steps 1 and 2 below for each component you plan to use
with the Commander.
Step 1: Entering the Code Number
1
See the supplied "Component Code Numbers", and find the code
number in double figures for the desired component.
If more than one code number is listed, use the number that's
listed first to complete the steps below.
For example, if you're setting up a Philips VCR, you would use
the code number 13.
If your component isn't listed, see "Searching for the Correct
Code."
VISUAL
mj
2
Set the
VISUAL/AUDIO
selector to
VISUAL
(to set up on the
TV, CABLE, AV1/DBS
or
VCR
position) or
AUDIO
(to set up on the
AMP,
TAPE, AV2
or
CD
position).
3
Set the slide switch to the position of the
i j
l
desired component.
• v ^" 1 '—' l_^_
J
Note
On each of the
CABLE, AV1/DBS, AMP, TAPE, AV2,
and
CD
positions, components are assigneciat the factory as shown in the
table in "Setting Up the Remote Commander."
But you can also assign other components on these positions. For
details, see "Changing the Component Type of the Positions."
4
Press and release the
S
(Set) button.
5
Enter the component's code number. For
example, if you're entering the code for a
PhiHps VCR, you would press and release
1,
then press and release
3.
6
Press and release the
ENTER
button to store the
code number in the Conunander's memory.
7
Go to "Step 2: Checking if the Code Number Works" to finish
setting up.
Step 2: Checking if the Code Number Works
1 Power on the component you want to set up.
2
Aim the Remote Commander at the component and press a button
to check if that button works.
For example, press the
POWER
button to see if it works on your
component.
3
Check that the other buttons of the Commander is operating the
corresponding functions of the component.
If the Commander Doesn't Seem to Be Working...
• First, try repeating these setup procedures using the other codes
listed for your component (see the supplied "Component Code
Numbers").
oo
Your Code
Number
(
enter
)
• If - after trying all the ccxies listed for your component - you still
cannot get the Commander to work properly, try the search
method describL*d in "Searching for the Correct Code."
Tip
Use the label (supplied) to write down the code numbers of your
components. Then affix the label to the back of the Commander.
Searching for the Correct Code
If you've tried all the code numbers listed for your component and
you still cannot get the Commander to work (or if your component is
not listed in the "Component Code Numbers" table), try these steps.
1
Power on the component you want to set up. Insert a tape or disc
if necessary.
2
Set the
VISUAL/AUDIO
selector and the slide
switch to the position that corresponds to the
component.
VISUAL
AUDIO
n r 1
1 1 1
^TV-j
CABLE-J*
—
i-AMP
ifTAPE
âvims-C
VCR—'
—
?-AV2
Leo
(ENTEf^
3
Press and release the
S
(Set) button.
4
Press and release the
CH+
button. Then press
and release the
POWER
button.
5
Repeat step 4 until the correct code number is found.
Each time you press the
CH+
button and then the
POWER
button,
a new code number will be transmitted.
Keep trying until your component operates by receiving the
transmitted signal from the Commander (e g., the power turns off,
the CH+ function works, playback starts, etc ). Be patient as you
do this; it may take 50 or 60 tries until the correct code number is
located.
6 When the correct code is found, press and
release the
ENTER
button to store the code
number in the Commander's memory.
7
Check that the Commander is operating the other functions of
your component by pressing the corresponding buttons on the
Commander. If they seem to be working properly, you're done
setting up the Commander.
If the component does not operate properly, repeat steps 3 to 6 and
search for another code. As the searching always starts from 01, it
will stop again at the same code as the last searching. Pass the code
and continue searching until the next code by which the component
operates.
If you still cannot get the Commander to work properly, see
"Troubleshooting."
Changing the Component Type of the
Positions
At the factory, components are assigned to each position of the slide
switch as shown in the table in "Setting Up the Remote
Commander."
By completing the following procedure, you can change this setting
so that you can set up other components on any of these positions
except for the
TV
and
VCR
positions.
1
Set the
VISUAL/AUDIO
selector to
VISUAL
(to
set up on
CABLE
or
AV1/DBS
position) or
AUDIO
(to set up on
AMP, TAPE, AV2
or
CD
position).
2
Set the slide switch to the position whose
component type is to be changed.
Note
You cannot change the component type on the
TV
and
VCR
positions.
3
Press and release the
S
(Set) button.
4
Press and release the ■ (stop) button.
)
n r
1
I I I
f
TAPE
àvices-iy
VCR-I
r-Ava
Leo