Craftsman 139.53683 - Manual

CRAFTSMAN
OWNER’S MANUAL
Children operating or playing with a garage door
opener can Injure themselves or others. The
garage door could close and cause serious Injury
or death.
Install the receiver (or any additional push
buttons) out of the reach of children and away
from ail moving parts of the door and door
hardware, but where the garage door is visible.
Do not allow children to operate the push
button(s) or the remote control(s).
A moving garage door could injure someone
under it. Activate the opener only when the door
is properly adjusted, you can see it clearly, and
there are no obstructions to door travel.
DISCONNECT POWER TO THE GARAGE DOOR
OPENER BEFORE PROCEEDING.
The SECURITY+ Universal Remote Control
Conversion Kit consists of a receiver and remote
control(s). This accessory wili convert almost any garage
door opener to rolling code technology. The remote control
sends a coded signal from outside the garage. Inside the
garage, the plug-in receiver accepts the transmitted signal
and starts the door opener. With Security+, the code
between the remote control and the receiver changes with
each use, accessing over 100 billion new codes.
IMPORTANT: To improve the security of your opener,
discard your old remote controls and erase or reset
your code. For maximum security and range, you
must disable the existing receiver on your opener,
otherwise it could still activate your opener:
• If there is an external receiver, disconnect power to it.
• if it is an integrated receiver, either clip off the
component that feeds power to the receiver or
remove the tuning slug and antenna from the receiver
section. If you have a different brand of opener,
contact the manufacturer for additional information on
disabling the existing receiver.
• If you have a Sears opener with an SRT receiver,
erase the old codes by holding down the SRT button
for 6 seconds until the indicator light turns off.
• If you have code switches, reset them to a random
code and deactivate the receiver as follows: On the
opener panel, peel
back the lower right
corner of the label to
expose the tuning
slug (closest to the
antenna), as shown.
Remove the slug
with a small hex
head wrench and cut
the antenna wire.
»Wf UK ffc
t a B E ¡ a
I® ®
• •< Tuning
Slug
Peat back label
al comer
SKCURITYHF
Universal Remote Control
Conversion Kit
Model 139.53682 (With 1 Remote Control)
Model 139.53683 (With 2 Remote Controls)
To comply with FCC rutas, adjuslmants or modiffcationa of this raceivar and/or
transmitter are prohibited, axcept for changing the code setSng or replacing
the transmitter battery. THERE ARE NO USER SERVICEABLE PARTS.
NOTICE TO U. S. CONSUMERS:
Soma states prohibit the service or repair of garage door openers
whch cannot be made to comply with the safety standards contained
In UL 325 (1988 revision), in order to comply with both the letter and
the spirit of these laws, this universal remote control converter kit
should not be used wth any Sears Craftsman* garage door opener
manufactured prior to April 1,1982.
Actuator Cover
Power
Indicator
Light
SRT.
Indicator
Terminals
BellV/ire
Channels
Ught
Antenna
^ SRT (learn)
Actuator
Connect Bell Wire
to Garage Door
Opener Terminals
Beil Wire
OPEN RECEIVER: Insert a small screwdriver in slot on
receiver front panel as shown. Twist up actuator cover.
CONNECT RECEIVER AND OPENER: Remove about
1/4* of insulation from each end of the 2-strand bell wire.
Connect one end to the receiver screw terminals
(polarity is NOT required). Route wire along the
channels and out the bottom as shown.
Connect the other end of the bell wire to the two opener
terminal screws labeled “2" (white) and “1” (red),
“common" and “command” or the terminals used for the
push button control.
Use insulated staples (not supplied) to secure bell wire
between receiver and opener. Length of beil wire
depends on where the receiver will be installed. Replace
the actuator cover.
Choose a l20Vac polarized outlet for the receiver which
is OUT OF THE REACH OF CHILDREN. Plug receiver
into selected outlet. Return power to the opener.
Side two contains code setting instructions and service
information.