Craftsman 139.53674SRT - Manual (Page 32)

Operation of Your Opener
Activate the opener with any of the following;
• The Remote Control: Hold push button down until
the door starts to move.
• The Door Control: Hold push button down until the
door starts to move.
• The Outdoor Key Switch or Keyless Entry.
(See Accessories) '
When the opener is activated with the safety
reversing sensor installed and correctly aligned;
1. If open, the doof will close. If closed, the door will
open.
2. If closing, the door will reverse.
3. If opening, the door will stop (allowing space for
entry and exit of pets and for fresh air).
4. If the door has been stopped in a partially open
position, it will close.
5. If obstnjcted while closing, the door will reverse.
6. If obstructed while opening, the door will stop.
7. The garage door will reverse in the closing cycle when
the invisible beam is broken. If fully open, the door will
not dose when the beam is broken. The sensor has
no effect in the opening cyde.
If the sensor is not installed or not aligned correctly,
the door won't close from any remote control. You can
close the door with the Door Control, the Outdoor Key
Switch, or Keyless Entry, however, if you activate
them until down travel is complete. If you release them
too soon, the door will reverse.
The opener lights will blink for S seconds when the
safety reversing sensor causes the door to reverse.
The Opener Lights wilt turn on under the following
conditions: When the opener is initially plugged in; when
the power is interrupted: when frie opener is activated.
They will turn off automatically after 4-1/2 minutes or
provide constant light when the Light feature on the
Premium Control Console is activated. SECURITY+
models: Lights will also turn on when someone walks
through the open garage door. Bulb size is 75 watts
maximum.
f
Weak or broken springs could allow an open
door to fall (either rapidly or unexpectedly),
resulting in serious Injury, death or property
damage.
If possible, use the emergency
release rope and handle only when the door is
fully closed.
Manual disconnect
position
The lockout feature
prevents the trolley
from reconnecting
automatically. Pull the
emergency handle
down and back (toward
the opener). The door
can then be raised and
lowered manually as
often as necessary. To
disengage the lockout
feature, pull the
emergency handle
straight down. The
trolley will reconnect on
the next UP or DOWN
operation.
To open the door
manually:
The door should be
fully closed if possible.
Pull down on the red
emergency release
handle and lift the door
manually. To
reconnect the door to
the opener, press the
Door Control push
button.
Towards Oponeit
Lockout position
Controls (see page 18)
programming features, next page.)
Premium Console (cont.):
Lock feature: The Lock feature is designed to
prevent operation of the door from remote controls.
However, the door will
open and close from the
Door Control, the Outdoor Key Switch and the
Keyless Entry Accessories.
To activate: Press and hold the small round Lock
button for 2 seconds. The push button light will
flash as long as the Lock feature is on.
To turn off: Press and hold the Lock button again
for 2 seconds.The push button tight will stop
flashing. The Lock feature wilt also turn off
whenever the SRT button on the opener panel is
activated.
Operation of the Door
(SECURITY^ models: See additional
Press the lighted push button to open or close the
door.
Press again to reverse the door during the closing
cycle or to stop the door while it's opening.
Premium Console:
Light feature: Press the large round Light button. If
the opener light is off, it will turn on. If the opener
light is on, (even in the 4-1/2 minute automatic
cycle) it will turn off.
But if you use the Light button to turn the tights on
and then activate the opener, the lights will turn off
after 4-1/2 minutes.
The Light button will not control the opener lights
when the door is in motion.
32