Attwood 3800 Series Stainless Steel 2-Mile Sidelights User Manual

Page 2

Advertising

1. Connect one lead to the negative (-) post of the 12-volt supply.

Connect the other lead to a fused and switched positive (+) 12-volt
supply. Sidelights require 1-amp fusing per lamp: a 1-amp fuse
for the Bicolor Combination light, a 2-amp fuse for the Sidelight
Pair. Note that navigation rules require sidelights to be operated
separately from anchor lights. Use either two switches or a single
switch with three positions for off/anchor/running (See Figure 3).

ATTWOOD LIMITED WARRANTY
ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331
(“Attwood”) warrants to the original consumer purchaser that Attwood brand
products will be free from defects in materials and workmanship under normal
use and service for one year from the date of original consumer purchases.

This limited warranty is not applicable if the product has been damaged by
accident, improper installation, unreasonable or improper use, lack of proper
maintenance, unauthorized repairs or modifications, normal wear and tear,
or other causes not arising out of defects in materials or workmanship.

Attwood products are warranted for use on pleasure boats. Any other use—
including but not limited to commercial, racing, or non-marine use—are not
covered under this warranty. Attwood’s obligation under this warranty is limited
to repair of the product at Attwood’s plant or replacement of the products at
Attwood’s option without expense to the original consumer purchaser. Any
expenses involved in the removal, reinstallation or transportation of the
product are not covered by this warranty.

The product must be returned to Attwood’s plant at the address above,
postage pre-paid, and insured with proof of original purchase including date.
If Attwood is unable to replace the product and repair is not commercially
practical or cannot be timely made, or if the original consumer purchaser
is willing to accept a refund in lieu of repair or replacement, Attwood may
refund the purchase price, less an amount for depreciation. The acceptance
by Attwood of any product returned or any refund provided by Attwood shall
not be deemed an admission that the product is defective or in violation of
any warranty. Products that are replaced or for which a refund is issued
become the property of Attwood.

THIS WARRANTY IS ATTWOOD’S ONLY EXPRESSED WARRANTY OF
THESE PRODUCTS. NO IMPLIED WARRANTY INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, SHALL BE EXTENDED BEYOND
THE WARRANTY PERIOD STATED ABOVE FOR EACH PRODUCT.
ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES, FOR LOSS
OF USE OF THIS PRODUCT, NOR FOR ANY OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES, COSTS, OR EXPENSES.

Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you may have other rights which vary from
state to state.

2-Amp Fuse

Switch

Figure 3

2. Be sure base is seated into the gasket all the way around (See

Figure 4 Detail).

3. Insert two #10 stainless steel mounting screws and fasten them

to the deck. Tighten until gasket seals to deck.

4. To replace lens: Be sure flat rubber washer is positioned over

screw mounting hole between lens and lens cover. Seat lens so
the base tabs fit in the lens grooves and base screw mount lines
up with the lens screw hole.

Figure 4

Gasket

Lens

Lens
Groove

Base

Base Tab

Gasket

Lens Cover

Figure 5

5. Place stainless steel cover over lens. Reinstall screw into cover

(See Figure 5).

MAINTENANCE
To replace lamp: Remove the cover screw, lens cover, flat rubber
washer, and lens. You may need to pry the lens from the gasket
with a small flat screwdriver, starting in the front of the light.

Remove old lamp by rotating 1/8 turn counterclockwise and pulling
forward. Replace lamp with the proper bayonet bulb (Attwood Part
Number 912717). Carefully replace lens, flat rubber washer, and
lens cover on gasket to maintain the waterproof seal. Reinstall
cover screw.

Advertising