Dave Smith Instruments MONO EVOLVER KEYBOARD User Manual
Evolver keyboard, Operation manual
Advertising
Table of contents
Document Outline
- Evolver
- Keyboard
- Operation Manual
- Dave Smith Instruments
- 1210 Cabrillo Hwy N
- USA
- For Technical Support, email: [email protected]
- Quick Start 1
- FAQs 4
- Inside Evolver 7
- Signal Flow Diagram 8
- Global Parameters 10
- Program Parameters 14
- Sequencer Operation 27
- Arpeggiator 28
- Modulation Destination Table 28
- Modulation Source Table 28
- MIDI Implementation 28
- Hidden Functions 28
- Welcome…
- Register
- Quick Start
- The Programs were collected from previous Evolver and Poly Evolver patches, and a bunch of new ones were made up for the keyboard. Special thanks to Program contributors (past and present), including:
- Tim Ande
- Frequently Asked Questions
- Chaining Multiple Evolvers Together
- The Analog Side
- The Digital Side
- Audio Inputs and Outputs
- Display
- Destination
- Off
- No destination selected
- Osc 1 Freq
- Oscillator 1 Frequency
- OscAll Lev
- Oscillator All Level
- NoiseLevel
- Noise Level
- ExtInLevel
- External In Level
- Osc1 PulsW
- Oscillator 1 Pulse width
- FM Osc4>3
- Frequency Mod (FM) Amount; Osc 4 -> 3
- FM Osc3>4
- Frequency Mod (FM) Amount; Osc 3 -> 4
- RM Osc4>3
- Ring Mod (Amplitude) Amount; Osc 4 -> 3
- RM Osc3>4
- Ring Mod (Amplitude) Amount; Osc 3 -> 4
- Low Pass
- Lowpass filter frequency
- LP Split
- Filter Split –separation between left / right
- Resonance
- Resonance
- UCA Level
- VCA amount
- Fback Freq
- Feedback frequency
- Fback Amt
- Filter Amount
- Delay1Time
- Delay 1 Time
- Delay1 Amt
- Delay 1 Amount
- LFO 1 Freq
- LFO 1 Frequency
- LFO 2 Freq
- LFO 2 Frequency
- LFO 3 Freq
- LFO 3 Frequency
- LFO 4 Freq
- LFO 4 Frequency
- Additional Sequencer-Only Modulation Destinations
- Seq Clock
- Sequencer clock (BPM) multiplier
- Midi Note
- MIDI note number
- M Note Vel
- MIDI Velocity
- Modulation Sources
- Display
- Source
- Off
- No Source selected
- Sequence1
- Sequence 1
- FilterEnv
- Filter Envelope
- MIDI Implementation
- Global Parameters
- 0
- No destination selected
- 1
- Oscillator 1 Frequency
- 10
- Oscillator All Level
- 11
- Noise Level
- 12
- External In Level
- 13
- Oscillator 1 Pulse width
- 16
- Frequency Mod (FM) Amount; Osc 4 -> 3
- 17
- Frequency Mod (FM) Amount; Osc 3 -> 4
- 18
- Ring Mod (Amplitude) Amount; Osc 4 -> 3
- 19
- Ring Mod (Amplitude) Amount; Osc 3 -> 4
- 20
- Filter frequency
- 21
- Filter Split –separation between left / right
- 22
- Resonance
- 23
- Highpass Frequency
- 24
- VCA amount
- 25
- Pan
- 26
- Feedback frequency
- 27
- Feedback Amount
- 28
- Delay Time 1
- 29
- Delay Time 2
- 30
- Delay Time 3
- 31
- Delay Time All
- 32
- Delay Amount 1
- 33
- Delay Amount 2
- 34
- Delay Amount 3
- 35
- Delay Amount All
- 36
- Delay Feedback 1
- 37
- Delay Feedback 2
- 38
- LFO 1 Frequency
- 39
- LFO 2 Frequency
- 40
- LFO 3 Frequency
- 41
- LFO 4 Frequency
- Sequencer-only destinations
- 69
- Tempo Clock multiplier
- 70
- MIDI Note Out
- Modulation Sources
- 0
- No Source selected
- 1
- Sequence 1
- 9
- Filter Envelope
- Hidden Functions
- The following hidden functions are listed for information only; you should not normally have to use these. To select these, hold the Reset switch and hit:
- To calibrate the pitch and mod wheels:
- 1) Turn the mod wheel all the way off (down), and while also holding the pitch wheel off, hold the Reset switch and hit the LFO 1 switch. 2) Return the pitch wheel to center, and hold Reset and hit the LFO 2 switch. 3) Move the Mod wheel all the way on (up), and while also holding the pitch wheel all the way on, hold Reset and hit the LFO 3 switch.
- Dave Smith Instruments