Dyras BPSS-4129 - Manual (Page 6)

EN
BPSS-4129 BPSS-4129
10 11
3. At the end of the measurement a sound signal can be heard and the blood pressure and the pulse values
appear on the display. The measured values are automatically stored within the memory of the apparatus, as
well.
4. After measurements have been taken, the device can be shut down by pressing the “ON/OFF” button or will
automatically be switched off after 3 minutes if left unused.
Note: Wait about 5 to 10 minutes before starting a new measurement. This time is necessary for vessels to
recover their original status after measurement. Taking into consideration psychologic factors, for some
people a longer delay could be justified between two measurements.
Memory function:
After measuring, both blood pressure and pulse data will automatically be stored in the device’s memory. The
memory is able to store the last 120 measurements. When the memory is full the latest measurement data will
replace the earlier ones.
1. The memory function of the apparatus can be activated after the measurement, or with the apparatus
switched off. With pressing the START button once after the measurement, the results of the earlier
measurements can be displayed.
2. With pressing the “START” button again the data measured before can be displayed in a reverse chronological
order. You can see the symbol “No” and the number of the stored value.
To delete the data stored within the memory, first switch on the turned-off apparatus with pressing the “START”
button once, then press and hold the “ON/OFF” button until horizontal lines appear on the screen in the place of
the numbers.
DEVICE MAINTENANCE AND CLEANING
• When not in use, store the device in its plastic box in a dry, dust- and frostfree place. Do not expose to direct
sunlight, or to extreme external temperatures.
• If you do not want to use the blood pressure meter for an extended time, remove batteries from the battery
compartment.
• Clean both the cover and cuff of the device with a moist fluff-free cloth, then wipe it thoroughly dry with a
dry cloth.
• Completely dry the device before using or storing it.
• In order to obtain accurate and precise measurements, check the device yearly with your doctor.
• During cleaning, never submerge the device or its cuff into water or hold under a water tap.
• Do not dismantle the device.
• When cleaning the appliance, never use solvent (acetone, benzole, petrol, alcohol, etc.) as these may solve
the casing material, or the internal parts of the appliance if they get into. Do not use cleaning agents with
coarse or grinding effect.
• If you do not want to use the device for a long period of time, remove batteries from the battery
compartment as they can leak - caustic electrolyte spilled out may damage the device (in which case the
manufacturer’s warranty becomes void). In order to avoid damage, you must follow these instructions:
• Batteries must be put into the compartment with their correct polarity (+ and -), as marked on the battery
compartment.
• Never use new and used batteries together.
• Never use batteries of different manufacturer and type together.
• Used batteries must immediately be replaced by new ones. If you do not want to use the device for a long
time, remove batteries from the battery compartment.
USING OF APPLIANCE
Blood pressure measurement:
In order to obtain reliable measurements, do not do any strenuous physical activities before beginning
measurements. Rest for about 5 to 10 minutes before taking measurements. Just before or during measurements
do not eat, drink or smoke. Certain irregularities, e.g. changes in heartbeat, fibrillations might cause erroneous
measurement results.
1. Free your forearm by removing any clothes obstructing your arm’s skin, as
the blood pressure meter cuff needs to touch the skin surface. Do not wear
watches, bracelets etc. during measurement.
2. Rest your elbow on a table.
3. Open the velcro of the blood pressure meter and pass your hand through.
Tighten the device by using velcro at a distance of about 1 cm from your hand
as shown in the figure.
4. Turn your palm upwards, hold fingers and wrist in natural position during
measurement. Do not double your fist or let your wrist hang down. During the
measurement hold your forearm with your other hand as shown in the figure.
Blood pressure measurement process
1. Push down the “ON/OFF” button. All the symbols will appear on the display for a short time. This lets you
check the fail safe operating status of the display. After self-test, the sign “0” flashes a few times then the
meter begins pumping up the cuff.
2. The apparatus pumps up the cuff automatically to a magnitude of 190 Hg mm, then it decreases the pressure
gradually. In case of a higher blood pressure value the apparatus automatically pumps the cuff further twice
or three times for the sake of a successful measurement. During the measurement the symbol of pulse
marked with a heart blinks following the rhythm of the pulse.
User'sManual for BPSS-4129.indd 10-11 User'sManual for BPSS-4129.indd 10-11 2013.01.22. 10:39:08 2013.01.22. 10:39:08