Contemporary Research ICC/ICW-HE - Manual (Page 2)

ICC/ICW- HE Specifications
Physical
Size: 19" [483mm] wide x 1.75" [38mm] height (1RU) x 9" [229mm] deep
Weight: 3 lbs [1.36kg]
Enclosure: All aluminum with durable black powder coat paint
Mounting: Shelf or 19" equipment rack (mounting brackets included)
Front Panel
RF Out Adjust: Trims iCC-Net channel output, shipped set to +55 dBmV
RS-232 TX LED: Yellow LED, lights when receiving RS-232 data on Control or iC-Net RS-232 port
RS-232 TX LED: Yellow LED, lights when receiving RS-232 data on Control or iC-Net RS-232 port
RS-232 DIP Switch: Sets RS-232 baud rate (9600 - 38.4K), 8 data bits, no parity, 1 stop bit
Selects high/low sensitivity for RF In signal
Net LED: Green LED for iC-Net bus, flashes once per second if network is operating, device numbers agree
LED will flash twice per second if the number of present and expected devices do not match
COM LED: Yellow LED blinks when a valid command is received or system response sent through the Control port
Error LED: Red LED indicates a problem within the unit
Reset/Default: White button sends press and release response to PC software or control system
Emergency: Red button sends press and release response to PC software or control system
Rear Panel
Control RS-232: DB9 female, RS-232 data link to control system or PC
iC-Net RS-232: DB9 female, RS-232 data link to send iCW-Net over fiber or codec
I/O 1 & 2: 4-pin captive screw terminal for Input/Outputs 1 and 2
2 switch closures or inputs, max 50 mA, 24 VDC, switch to GND
I/O Applications: DC power - close pins 1 & 3 to provide DC on/off
Dry closure 2 - close pins 3 & 4 for dry contact to external power relay, AMX PC1 or similar
Sense closure (3 & 4) on Input 1 - trigger control system to power off for all rooms
iCW-Net Connections (ICC-HE and ICW-HE)
iCW-Net 2, 3: RJ-45 female 8 pin Telco jack, supports 3300 ft [1 km] of wire
RS-422 type data requiring at least 2 twisted wire pairs with shield or fifth conductor
iCW-Net 1: 6-pin captive-screw terminal for system wiring or use with RS-422-format fiber or codecs
iC-Net Expand: RJ-11 female 6-pin Telco jack
CAT3/CAT5 compatible unshielded, max 3,300 feet [1 Km] from Head End
Power In: 2.1mm coaxial jack (inside center conductor positive), 300 mA maximum
11 to 18 VDC, 12 VDC typical (may be unregulated)
iCC-Net Connections (ICC-HE Only)
RF In: 'F', female, 75 ohm impedance, RF and iCC-Net from CATV system
Data Receive: Carried over the same RF coax connection as TV channels
Return signal from system controllers
Sub-band, 5.6MHz, narrow-band signal below standard sub-band channels
-15 to +35 dBmV signal level (0 to +15 dBmV nominal)
RF Out: ‘F', female, 75 ohm impedance, RF to CATV distribution to TVs, tuners, and controllers
Data Transmit: Mid-band VHF, 74.7 MHz, narrow-band signal between channels 4 and 5
± 80 KHz max carrier deviation
+55 dBmV maximum (default)
Includes
19" Mounting hardware
10 dB RF attenuator (ICC-HE only)
12 VDC Power Supply (North American shipments only)
Contemporary Research z 17630 Davenport z Suite 113, Dallas, Texas z 75252-5963
Phone: (972) 931-2728 z Toll Free: (888) 972-2728 z Fax: (972) 931-2765
Doc 5002-025 1002 © 2002, specifications subject to change without notice