Pridiom WIRE CONTROLLER OF AIR CONDITIONER KJR-12B/DP(T)-F Installation Manual User Manual

Wire controller installation manual

Advertising
background image

1
2

3
4

5
6

7

1

1

1

3

3

1

2

1

2

3

1

1

1

SAFETY PRECAUTION

Read the safety precautions carefully before installing the unit.
Stated below are important safety issues that must be obeyed.
Conform there is no abnormal phenomena during test operation after complete, then
hand the manual to the user.
Meaning of marks:

WARNING

CAUTION

Means improper handling may lead to personal death or

severe injury.

Means improper handling may lead to personal injury or

property loss.

OTHER PRECAUTIONS

Installation Location

Do not install the unit in a place with much oil, steam, sulfide gas. Otherwise, the

product may deform and fail.

Preparation before installation

1. Check whether the following assemblies are complete.

No.

Name

Qty.

Remarks

2. Prepare the following assemblies on the site.

No.

Name

Qty.

Type

Remarks

5-core shielded cable

Switch box

Wiring Tube(Insulating

Sleeve and Tightening

Screw)

Note to installation of wire controller:

INSTALLATION PROCEDURE

Installation description:

When it is necessary to use this controller,it needs to add a small 5-terminal

Group and fasten a infrared emmiter near to the receiver in the switch board.

Connecting the anode and cathode to A、B of the Terminal Group, also

connect +5V、GND、RUN of the switch board separately to the C、D、E of

the 5-terminal Group.

WARNING

CAUTION

CAUTION

1. This manual contains information about the procedure of installing wire controller.

Please refer to Indoor Unit Installation Manual for connecting between Wire Controller and

Indoor Unit.

2. Install the Wire joint,5p to the appointed position of the electric controlling Box.

3. Circuit of Wire Controller is low voltage circuit, Never connect it with a standard

220V/380V circuit or put it into a same Wiring Tube with the circuit, and the interval must

be more than 300~500mm.

4. The shield cable must be connected stable to the ground, or transmission may fail.

5. Do not to attempt to extend the shield cable by cutting, if it is necessary, use Terminal

Connection Block to connect.

6. After finishing connection, do not use Megger to have the installation check to the signal

wire.

The connecting wire should be a little longer as to take away the switch board easily for

maintenance

The connecting wire should be a little longer as to take away the controller easily for

maintenance..

Please entrust the distributor or professionals to install the unit.

Installation by other persons may lead to imperfect installation, electric shock or fire.

Strictly follow this manual.

Imporper installation may lead to electric shock or fire.

Reinstallation must be performed by professionals.

improper installation may lead to electric shock or fire.

Do not disassemble your air conditioner at will.

A random disassembly may cause abnormal operation or heating, which may result in fire.

Do not install the unit in a place vulnerable to leakage of flammable gases.

Once flammable gases are leaked and left around the wire controller, fire may occure.

The wiring should adapt to the wire controller current.

Otherwise, electric leakage or heating may occur and result in fire.

The specified cables shall be applied in the wiring. No external force may be applied

to the terminal.

Otherwise, wire cut and heating may occur and result in fire.

WIRE CONTROLLER INSTALLATION MANUAL

Thank you very much for purchasing our product.

Before using your unit, please read this manual carefully and keep it for future reference.

Version: MDV06I-002EW

202000100067

MODEL: KJR-12B/DP(T)-E

KJR-12B/DP(T)-E(C)

KJR-12B/DP(T)-F

1

2

Wire controller

Wood Mounting Screw

GB950-86 M4X20(For Mounting on the Wall)

Mounting Screw

GB823-88 M4X25(For Mounting on the Electrical Switch Box)

Installation Manual

Owner's Manual

5-terminal Group

Terminal Installation Screw

RS9005E

ST3.9x12-F-H GB845-85

RVVP-0.5mm

2

x5

The longest wire is 15m

Wires here adopts 5-core Shield

Cable,the length should be accord

with the actual conditions .

Wiring technique and principle:

Wire Controller

B

A

5-terminal Group

C
D
E

Wood Mounting

Screw (M4X20)

Turning cover

Wire Control Board

LCD display

Front cover of

Wire Controller

Back cover of

Wire Controller

For the Terminal Group is standing

out of the back cover, so it is

necessary to obligate holes, and

it is forbiden to fasten difectly to the

wall!!

While installing, using Screwdriver or other

tools to open the back cover from the inside

After the back cover is

fastened, to fix up the

front cover first lock

one of the two then the

another.

1. Wiring diagram between wire controller and four-way cassette of indoor unit

2. Wiring diagram between wire controller and duct type of indoor unit

3. Wiring diagram between wire controller and high static duct type of indoor unit

A

B

C

D

E

A B C D E

5-core Connecting Wire Group

10-core Connecting

Wire Group

Signal Receiver

Plane of Indoor Unit

5-core Shield Cable

Connecting to wire controller

Wire Terminal Group Connecting Extended Figure

Indoor Unit Electric Controlling Box

Plug 10 of Electric Controlling Box

Main Board

Wire Terminal Group

Grounding

Signal Receiving
Board

Plane of Indoor Unit

Indoor Unit Electric Controlling Box

Plug Cn10 of Electric Controlling Box

Main Board

Signal Receiving
Board

Signal Receiver

10-core Connecting

Wire Group

5-core Connecting Group

5-core Shield Cable

A

B

C

D

E

A B C D E

Connecting to wire controller

Wire Terminal Group Connecting Extended Figure

Wire Terminal Group

Grounding

A

B

C

D

E

A B C D E

Connecting to wire controller

Wire Terminal Group Connecting Extended Figure

Wire Terminal Group

Grounding

5-core Shield Cable

10-core Connecting Group

5-core Connecting Group

Signal Receiving Board

Indoor Unit Electric Controlling Box

Plug Cn10 of Electric Controlling Box

Main Board

Signal Receiving Board

A B C D E

Back of Wire Controller

A B C D E

Back of Wire Controller

A B C D E

Back of Wire Controller

Advertising