Thetford N500 Series Installation Manual - Manual (Page 6)

Installation Manual 6
Connect the Electrical Components
NOTE: The current draws are nominal values.
N400 models
AC Operation 120 volts AC voltage
(108 volts min. - 132 volts max.)
Current Draw 1.8 Amps at 110 volts AC
2.0 Amps at 120 volts AC
Propane Gas
Operation 12 volts DC control voltage
(11.5 volts min. - 15.4 volts max.)
Current Draw .37 Amps at 12 volts DC
.42 Amps at 15 volts DC
DC Operation 12 volts DC
(N400.3 only) (11.5 volts min. - 15.4 volts max.)
Current Draw 14.1 Amps at 12 volts DC
16.5 Amps at 14 volts DC
N500 models
AC Operation 120 volts AC voltage
(108 volts min. - 132 volts max.)
Current Draw 1.8 Amps at 110 volts AC
2.0 Amps at 120 volts AC
Propane Gas
Operation 12 volts DC control voltage
(11.5 volts min. - 15.4 volts max.)
Current Draw .13 Amps at 12 volts DC
.15 Amps at 14 volts DC
DC Operation 12 volts DC voltage
(N500.3 only) (11.5 volts min. - 15.4 volts max.)
Current Draw 14.1 Amps at 12 volts DC
16.5 Amps at 14 volts DC
N510 models
AC Operation 120 volts AC voltage
(108 volts min. - 132 volts max.)
12 volts DC control voltage
(10.5 volts min. - 15.4 volts max.)
Current Draw 1.79 Amps at 110 volts AC
1.92 Amps at 120 volts AC
Propane Gas
Operation 12 volts DC control voltage
(11.5 volts min. - 15.4 volts max.)
Current Draw .37 Amps at 12 volts DC
.42 Amps at 15 volts DC
DC Operation 12 volts DC control voltage
(N510.3 only) (10.5 volts min. - 15.4 volts max.)
Current Draw 14.1 Amps at 12 volts DC
17.0 Amps at 15 volts DC
This refrigerator operates on both AC and DC electrical
sources. Operation out of these limits may damage the
refrigerator’s electrical circuit parts and will void the warranty.
Connect the 120 volt AC supply:
WARNING: Connect the AC power cord only to a
grounded three-prong receptacle. Do not remove the
round ground prong from the power cord. Do not use a
two-prong adapter or an extension cord. Operation of the
refrigerator without correct ground can cause dangerous
electrical shock or death if you are touching the metal
parts of the refrigerator.
4. Install the door:
- Put the door down onto the lower hinge pin.
- Align the holes in the upper hinge and the filler plate and
hold in this position.
- Screw the upper hinge pin down into the upper hinge and
into the door.
- Tighten all of the screws.
- Make sure the travel latch fully engages the travel latch
plate.
- The travel latch should engage the travel latch plate .2
inches.
- If not, loosen the screws and adjust the height of the
travel latch.
- Tighten the screws.
Change the travel latch position:
This refrigerator allows you to put the travel latch either at the
top of the door or at the bottom of the door regardless of the
door swing direction (See Art01570 and Art01572).
1. Change the position of the travel latch plate:
- Remove the screw [6] from the travel latch plate [7] on the
door.
- Remove the screw [6] from the filler plate [8] on the oposite
end of the door.
- Put the travel latch plate on the opposite end of the door.
- Attach the travel latch plate with the screw.
- Put the filler plate on the opposite end of the door.
- Attach the filler plate with the screw.
2. Change the position of the travel latch:
- Remove the screws from the travel latch [5].
- Put the travel latch on the opposite end of the refrigerator.
- Attach the travel latch with the screws.