TrendsAudio TA-10.2 Class-T Stereo Amp/Power Amp - Manual (Page 4)

Trends TA-10 User Guide
Section 5 Specifications 7
5 5 . . S S p p e e c c i i f f i i c c a a t t i i o o n n s s
5.1 Specification of the Amplifier Unit
T-Amp IC Tripath TA2024
Output Power 2x15W @4ohm
2x10W @8ohm
Signal-to-Noise Ratio (SNR) 98dB
Dynamic Range 98dB
IHF IM Distortion 0.10% @ 1W, 4ohm
THD+Noise Audiophile Quality
0.03% @ 9W 4ohm
0.1% @ 11W 4ohm
0.1% @ 6W 8ohm
High Power
10% @ 15W 4ohm
10% @ 10W 8ohm
Power Efficiency 81% @ 15W 4ohm
90% @ 10W 8ohm
Input Audio IN RCA (Left/Right) x 1
Power Socket (5.5mm/2.1mm) x 1
Output Speaker OUT (Left) x 1 pair (+/-)
Speaker OUT (Right) x 1 pair (+/-)
Other Switch & Knob Power ON/OFF switch x 1
Power Indicator (Blue LED) x1
Volume Knob x 1 ( no Volume Know for TA-10.2P)
Power Supply DC 12V-13.2V (max.)
Dimensions(DxWxH) 114mm x 76mm x 46mm[case only]/150mm[incl. sockets &
knob] for stereo amplifier
114mm x 76mm x 46mm[case only]/135mm[incl. sockets &
knob] for power amplifier
Weight 500g
5.2 Specification of the AC Adaptor
Model Standard SE Version
AC Input: Universal AC 100V-240V/50-60Hz 100V-240V/50-60Hz
DC Output DC 12V 3A (36W) DC 12V 4A (48W)
Ripple & Noise <= 50mV <= 50mV
Over-load Protection 105%-150% 105%-150%
Over-voltage Protection 115%-150% 115%-150%
Dimensions(DxWxH) 117mm x48mm x33mm 117mm x 58mm x 38mm
Weight 300g 400g
5.3 Optional Accessories: Trends PW-10 PSU
AC Input 110V /50~60 Hz or 220V / 50~60Hz(specific model should be
selected, not compatible)
DC Output TA: +12V/3.3A, DA/UD: +5V/230mA, PA: +24V/420mA
AC Input Socket: IEC socket
DC Output Socket: DC 2.1 socket
Dimensions(DxWxH) 205mm x 105mm x 55mm
Weight 1.8KG
Trends TA-10 User Guide
Section 6 Troubleshooting / Section 7 Accessories / Section 8 Contact Us 8
6 6 . . T T r r o o u u b b l l e e s s h h o o o o t t i i n n g g
If your machine is out of order, it may not be very serious. Before you call your local
distributor or us to repair, you are suggested to check the following:
Symptoms Possible Reasons Handling Methods
power cords not properly
connected
properly connect the power
cords
cannot power ON
indicator not bright
power switch is OFF switch ON the power
the volume level is too low turn volume level higher
the audio cable not properly
connected
properly connect the audio
cable
the audio source (e.g. CD
player) not started playing
start playing the audio source
the audio source is mute or
connected with a headphone
(some player may auto-mute
the audio output when the
headphone is connected)
Disable the mute or unplug
the headphone connected, if
any.
no sound at all
the speaker cables not
properly connected
properly connect the speaker
cables
volume level cannot be adjust
by turning the volume knob
the amplifier configured as
pure power amplifier by
setting the jumpers in J2
reset the jumpers in J2 back
to integrated amplifier
7 7 . . A A c c c c e e s s s s o o r r i i e e s s
• AC adaptor x1
• 3 pins power cord x1 (IEC female plug and male plug for your country standards)
• User Guide x1
• Warranty Card x1
* To continuously improve our product, we reserve the rights to change some
specifications without further notice.
8 8 . . C C o o n n t t a a c c t t U U s s
ITOK Media Limited (Trends Audio)
Address: Unit E,13/F.,World Tech Centre,
95 How Ming Street, Kwun Tong, Kowloon, Hong Kong
Phone: +852 2304 0730 (9am-6pm, HKG Time)
Fax: +852 2566-5740
Email: [email protected] (Sales)
[email protected] (Support)
Web: http://www.TrendsAudio.com