Voltage Valet 2TS User Manual

Lcd travel clock, Model 2ts

Advertising
background image

ONE YEAR WARRANTY

We guarantee each new LCD Travel Clock to be

free from defects in material or workmanship and

to perform under normal use and service. This

guarantee shall run for a period of one year from

the date of purchase, and obligations under this

guarantee are limited to remedying any defect or

replacing any defective part and shall be effective

only if the defective unit is returned to us within 12

months after purchase. Damage due to abuse,

misuse, or overloading is not covered by this

guarantee. We shall not be responsible for any

other loss or damage that may arise through the

use by a purchaser or others of this device, and the

purchaser assumes such responsibility and will

hold Hybrinetics, Inc. harmless in respect to all

such loss or damage.

Important:

Important: This is a factory direct warranty. Do not

return defectives to your retailer. All defectives

must be returned to the factory accompanied by a

sales receipt with the original date of purchase. For

more information please call our toll free number:

(800) 247-6900.

Voltage Valet Division, Hybrinetics, Inc.

Voltage Valet Division, Hybrinetics, Inc.

225 Sutton Place, Santa Rosa, CA 95407

e-mail: [email protected]

www.voltagevalet.com

© 2005 Hybrinetics,Inc.

SETTING THE TIME:
1. Slide the function switch (e) to the “T.SET” (time

set) position.

2. Press the hour button (a) to advance the display

to the desired hour.

3. Press the minute button (b) to advance the

display to the desired minutes.

4. In 12 hour format a PM indicator will appear for

PM time.

SETTING THE ALARM TIME:
1. Slide the function switch (e) to the “AL.SET”

(alarm set) position, colon (:) between hours and

minutes stops blinking.

2. Press the hour button (a) to advance the display

to the desired alarm hour.

3. Press the minute button (b) to advance the

display to the desired alarm minutes.

4. In 12 hour format a PM indicator will appear for

PM time.

ACTIVATING THE ALARM AND SNOOZE:
1. Slide the function switch (e) to the “AL.ON”

(alarm on) position. The alarm symbol (Z) will

appear on the display.

2. The alarm will activate at the pre-set time and

sound for 60 seconds.

3. When the alarm activates you may press the

snooze/light button (c), The alarm will stop and

activate again after approximately 4 minutes.

This may be repeated over and over again.

4. Slide the function switch (e) to the “AL.OFF”

(alarm off) position to shut off the alarm.

DISPLAY FORMAT:
1. Slide the format switch (d) to either the 12-hour

or 24 hour format.

DISPLAY LIGHT:
1. To activate the display light, press the

snooze/light button (c).

LOW POWER LED BACKLIGHT:
1. To operate the LED backlight, simply slide the

function switch (e) to the “AL.ON” (alarm on)

position. (i.e. BACKLIGHT ON), The display will

stay illuminated in a dark environment until you

slide the function switch (e) to the “AL.OFF”

(alarm off) position.

2. The LED backlight may be used up to eight (8)

hours per day with the battery life of

approximately six (6) months. The less the LED

backlight function is used, the longer the battery

life.

NIGHTLIGHT & FLASHLIGHT:
1. To activate the nightlight, slide the function

switch (f) all the way down and slide the function

switch (e) to the “AL.ON” (alarm on) position. A

gentle light will appear.

2. To activate the flashlight, slide the function

switch (f) all the way down, pressing further

downward and holding to activate the flashlight.

The flashlight may also be activated by pressing

the snooze/light button (c). Frequent use of the

flashlight will affect the battery life.

BATTERY INFORMATION:
This clock is designed to operate using three (3)

1.5V “AAA” alkaline batteries (not included).

1. Remove the battery cover, by pushing in on the

grooved portion of the Battery Cover (g) and

sliding it away from the clock body..

2. Insert the batteries, observing the +/- polarity

symbols indicated inside the compartment.

3. Replace the battery cover.

4. Do not mix alkaline and non-alkaline type or old

and new batteries. Dispose of old batteries in a

responsible manner.

MAINTENANCE:
The batteries should be replaced if the display or

alarm becomes weak or dysfunctional. Store the

clock without batteries when not in use. A soft cloth

or a paper towel may be used to clean your clock.

Do not use any corrosive cleanser or chemical

solutions on the clock. Keep the clock clean and dry

to avoid any problems.

Lighted Display Stays on All Night

LCD Travel Clock

P

(a) hour set

(b) minute set

(d) 12/24 hours switch

(c) snooze/light button

(e) switch to set time, alarm time,


alarm on/off, backlight on

(f) switch to set flashlight,


nightlight, or light off

(g) batter

y cover

Model 2TS

Model 2TS

Advertising