Ryobi A99DLK2 - Manual

WOOD anD metal DOOR
lOCK InStallatIOn KIt
a99DlK2
WaRnInG:
To reduce the risk of injury, do not attempt to use this
product until you have read thoroughly and understand
completely this operator’s manual and the operator’s
manual for any power tools used.
PaCKInG lISt
See Figure 1.
Bracket
1 in. Spade Bit
1 in. Bimetal Hole Saw
1-1/2 in. Bi-metal Hole Saw
2-1/8 in. Bi-metal Hole Saw
Hole Saw Adaptor (2)
Arbor with Pilot Bit
1/8 in. Brad Point Drill Bit
3/32 in. Brad Point Drill Bit
PH2/8-10SL Double Ended Bit
tOOlS neeDeD
AC Power Drill or DC Drill 18 Volts or more
aPPlICatIOnS
You may use this tool for the following purpose:
 Installing lock sets and dead bolts easily and accurately
without measuring.
InStRuCtIOnS
See Figures 2 - 7.

Select desired backset by sliding yellow backset plate in
corresponding slot.
nOte: Be sure backset location, and hole size are correct
by reading instructions included with hardware before
drilling.
 Position the bracket on the door using auto-strike locator.
Line up auto-strike locator with center of the mortise in the
door jamb and slide into mortise.
 Drill cross bore hole first. Choose proper size hole saw.
nOte: For 2-1/8 in. hole saw, remove hole saw guide. For
1-1/2 in. hole saw, the hole saw guide should remain in
bracket.
 Assemble arbor with pilot bit into correct hole saw. Tighten
securely.
 Follow drill manual instructions to install hole saw into
chuck.
 For a straight hole, be sure drill is at a right angle to the door
so the hole saw enters the hole guide and door evenly.
 Drill from one side until pilot bit shows on opposite side
of door. Drill on opposite side, lining up pilot bit hole with
pilot bit. Meet the two holes in the center of door.
 Using the 1 in. hole saw, drill latch bore. Keep drill at a
right angle to door flat to ensure straight hole.
nOte: Some hardware requires latch bore to extend
beyond cross bore hole. In this case, use 1 in. spade bit
to drill beyond cross bore hole.
 Follow directions included with door hardware for
instructions on installing. Use included tools to install
hardware.
If installing a lock set with a rectangular, flush mounted
strike plate, use the RYOBI Door latch Installation Kit
(model# a99lm1)
Fig. 1
A - Bracket (support, suporte)
B - Auto-strike locator (localisateur à martelage automatique, indicador de
posición con golpe automático)
C - 2-3/4 in. auto-strike slot [fente pour martelage automatique de 69,85
mm (2-3/4 po), ranura de golpe automático de 69,85 mm (2-3/4 in)]
D - 2-3/8 in. auto-strike slot [fente pour martelage automatique de 60,33
mm (2-3/8 po), ranura de golpe automático de 60,33 mm (2-3/8 in)
E - Hole saw guide (guide de scie-cloche, guía de la sierra de perforación)
F - Backset plate (plaque d’appui, placa de distancia al centro del
picaporte)
B
A
E
Fig. 2
Fig. 4
C
A - Bracket (support, suporte)
B - Adaptors (adaptateurs, adaptadores)
C - 1 in. bi-metal hole saw [scie cloche bimétal de 25,4 mm (1 po), sierra de
perforación bimetal de 25,4 mm (1 pulg.)]
D - 1-1/2 in. bi-metal hole saw [scie cloche bimétal de 38,1 mm (1-1/2 po),
sierra de perforación bimetal de 38,1 mm (1-1/2 pulg.)]
E - 2-1/8 in. bi-metal hole saw [scie cloche bimétal de 53,98 mm (2-1/8 po),
sierra de perforación bimetal de 53,98 mm (2-1/8 pulg.)]
F - 1 in. Spade bit (foret à trois, pointes de 25,4 mm (1 po) broca de pala de
25,4 mm (1 pulg.)
G - Arbor with pilot bit (arbre avec mèche pilote, mandril con broca pilato)
H - 1/8 in. Drill bit [foret de 3,18 mm (1/8 po), punta de destornillador de
3,18 mm (1/8 pulg.)]
I - 3/32 in. Drill bit [foret de 2,4 mm (3/32 po), punta de destornillador de
2,4 mm (3/32 pulg.)]
J - PH2/8-10SL Double ended bit (embout double 8-10SL nº 2, broca de
doble extremo 8-10SL N.º 2)
Fig. 3
Fig. 5
Fig. 6
A
A - Cross bore (trou transversal, orificio transversal)
B - Backset (appui, distancia al centro del picaporte)
C - Latch bore (trou du loquet, orificio del pestillo)
D - Center mark (point central, marca de centro)
B
C
D
D
20
15
A
J
I
H
B
E
F
D C
G
A - Arbor with pilot bit (arbre avec mèche pilote, mandril con broca pilato)
B - Hole saw with adaptor (a scie-cloche avec adaptateur, la sierra de
perforación conadaptadore)
C - Hole saw assembly (assemblage de la scie-cloche, conjunto de la sierra
de perforación)
A
B
C
D
DRILL CROSS BORE
PERCER LE TROU TRANSVERSAL
PERFORAR ORIFICIO TRANSVERSAL
DRILL LATCH BORE
PERCER LE TROU DU LOQUET
PERFORAR ORIFICIO DEL PESTILLO
A - Bracket (support, suporte)
B - Auto-strike locator (localisateur à martelage automatique, indicador de
posición con golpe automático)
C - Mortise (mortaise, mortaja)
Fig. 7
A B
C
F