Waterworks R.W. Atlas Low Profile Concealed Tub Filler With Handshower and Metal Lever Handles - Manual (Page 2)

PRODUCT SUPPORT 800.927.2120 8am - 6pm EST
RW ATLAS
Low Profile Concealed Tub Filler with Handshower
INSTALLATION GUIDELINES
Page 2 of 3 1.15.2013
These guidelines have been prepared for the professional contractor to aid in the installation of:
RW ATLAS LOW PROFILE CONCEALED TUB FILLER WITH HANDSHOWER WITH METAL WHEEL
HANDLES (STYLE# RWTF01) & METAL LEVER HANDLES (STYLE # RWTF10).
All dimensions are based on original specification and are subject to change and variation.
Please consult your Design Associate for current specifications.
SEE SERVICE PART DOCUMENT FOR PART ORDERING, AVAILABLE ON WATERWORKS.COM
SPOUT INSTALLATION:
¾ See Figure 1. for Steps 1-3.
1. Remove the tee, tee rubber washer, nut, metal
washer & spout rubber washer from the bottom of
the spout.
2. Insert the spout into the hole on the mounting
surface making sure the o-ring is underneath the
spout.
3. Re-install rubber washer, metal washer and tighten
the nut, to secure the spout. Re-attach the tee
making sure the rubber washer is in the outlet.
Figure - 01
SPOUT
SPOUT
O-RING
SPOUT RUBBER WASHER
SPOUT METAL WASHER
NUT
TEE RUBBER WASHER
TEE
HANDLE INSTALLATION:
¾ See Figure 2. for Steps 4-9.
4. Unthread the handle assembly from the valve body,
also removing the hex collar, escutcheon and o-ring.
5. Thread the nut all the way down the valve body and
insert it through the hole on the underside of the
deck. When the valve body is sticking through the
hole, thread on the escutcheon making sure the o-
ring is between it and the deck.
6. Thread the handle assembly onto the cartridge of
the valve body, making sure the hex collar is
between the handle assembly and the escutcheon.
7. If there is a gap between the handle assembly and
hex collar, un-thread the escutcheon up to meet the
handle assembly.
8. Tighten the nut up against the bottom of the deck
to secure the handle.
9. Connect outlet hose from valve body side outlet to
tee.
10. Connect 3/4" supply line (NOT SUPPLIED) to
bottom inlet on side valve.
11. Repeat steps 4-8 to install second handle.
Figure - 02
TEE
HANDLE ASSEMBLY
HEX COLLAR
ESCUTCHEON
O-RING
RUBBER WASHER
PLASTIC WASHER
NUT
VALVE BODY
OUTLET HOSE
HANDSHOWER INSTALLATION:
¾ See Figure 3. for Steps 12-18.
12. Remove the nut and rubber washer from the bottom
of the threaded tube. Unthread the retaining collar
from the top of the threaded tube and remove the
plastic sleeve.
13. Loosen the hex collar and insert the threaded tube
along with the escutcheon and hex collar into the
hole in the deck, making sure the o-ring is between
the escutcheon and the deck.
14. Re-attach the rubber washer and nut to the
threaded tube from under the deck.
15. Slide the retaining collar over the conical end of the
handshower hose and insert the hose into the plastic
sleeve. Pass the knurled end of the hose through the
threaded tube until the plastic sleeve is fully seated
inside the threaded tube. Thread the retaining collar
back onto the threaded tube.
16. Thread the hex collar up until it touches the
retaining collar, then fully tighten the nut to secure
the assembly to the deck.
17. Connect the conical end of the hose to the
handshower. NOTE: A flow restricting check valve is
located in the inlet of the handshower.
18. Connect the female end of the flex hose to the
check valve housing on the tee, then connect the