Rane MA 3 1998 version - Manual (Page 4)

Manual-4
MA 3 LIMIT & vs 31 MAR 98 08:52:13
0.020
0.1
1
2
THD+N(%)
10.00
15.00
20.00
25.00
30.00
35.00
40.00
45.00
50.00
55.00
60.00
LEVEL(W)
-5.00 0.0 5.000 10.00 15.00 20.00
AMPL(dBu)
FEATURES & APPLICATIONS
Built to be driven hard
The MA 3 Amplifier drives all three Channels at the
continuous average rated power, indefinitely. It is specifically
designed to operate in demanding commercial applications.
Very low emissions allow the Amplifier to operate in close
proximity to signal processing equipment without causing
excessive interference. The CP 31, CP 52, CP 64 and SRM 66
may all operate next to the MA 3 in a rack. The high effi-
ciency “heat tunnel” design allows the Amplifier to process
severely compressed signals reliably even when installed in a
rack with elevated ambient temperatures. Forced air cooling
keeps heat away from other equipment.
You won't hear other Zones
The MA 3 is designed to deliver foreground music,
background music and paging signals to three different Zones
without annoying crosstalk. A quiet office, for example, with
a paging signal only, will not hear foreground music playing
in the lounge. The high capacity linear power supply incorpo-
rates three independent secondary supplies with independent
bridge rectifiers and filters. The result is exceptionally good
crosstalk figures even with multiple channels driving full
power into 4 ohm loads.
It’s OK to light the 0 dB Headroom indicator a lot
The high performance Limiter used in the MA 3 means all
the available power can be delivered to the load and not
simply held in reserve to avoid overload. There is no need to
buy up to four times the required power just to prevent
occasional system overload. The MA 3 can compress a signal
with 9 dB of dynamic power range down to a signal with 3 dB
of dynamic power without loss of speech intelligibility or
excessive distortion.
With typical Amplifiers, when 40 watts is needed to
achieve a required average SPL of 80 dB, the contractor must
buy an Amplifier rated at no less than 160 watts just to
maintain 6 dB of headroom. The figure below illustrates the
performance of the MA 3 Limiter.
No bad “spikes”
The MA 3 is designed to operate without interruption of
signal with as little as 85 VAC available (120 VAC unit).
Even if the Amplifier is operating at full power, the signal
will not breakup as the AC line voltage drops to 85 VAC. If
the AC line drops lower than 85 VAC the signal mutes
without “spikes.” Once AC power is restored, the signal
restarts quickly without “spikes” or signal breakup.
The good “SPiKe”
The power Amplifiers in the MA 3 are protected with
National Semiconductors’ proprietary SPiKe* protection
circuitry. SPiKe protection offers a level of protection not
available in conventional amplifiers. It has the ability to
instantaneously monitor the temperature of the power device
die, yielding a level of reliability not achievable with discrete
designs.
80 Hz Highpass Filters
Internal jumpers allow independently selecting 80 Hz,
2 nd -order Butterworth Filters for each Channel. These Filters
are useful when using small bookshelf speakers or small
constant voltage distribution transformers.
Optional constant voltage distribution transformers
Up to three 70.7 V or 100 V constant voltage distribution
transformers may be mounted inside the MA 3. The optional
TF 407 is a 40 watt, 70.7 V transformer with 0.5 dB insertion
loss at rated power and a frequency response of 50 Hz to 15
kHz, ±1 dB. The optional TF 410 is a 40 watt, 100 V trans-
former with .5 dB insertion loss at rated power and a fre-
quency response of 50 Hz to 15 kHz, ±1 dB. No external
wiring or mounting is required.
105227
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.com
*Spike is a registered trademark of National Semiconduc-
tor Corporation. SPiKe is an acronym for Self Peak Instanta-
neous (Ke) protection circuitry.
Input Level in dBu
THD & N in % Output Power in Watts
Power
→ ←
THD & N