Rane MQ 302S - Manual (Page 9)

Manual-8 All features & specifications subject to change without notice. 102945
©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL (425)355-6000 FAX (425)347-7757 WEB http://www.rane.com
MOJO GLOSSARY
balanced line The recommended method of interconnecting audio
equipment. A balanced line requires three conductors: a twisted-pair
for the signal (positive and negative) and an overall shield. The
shield must be tied to the chassis at both ends for hum-free intercon-
nect.
bandwidth Abbr. BW The numerical difference between the upper
and lower -3 dB points of an audio band.
clipping What occurs when a unit tries to produce a signal larger
than its power supply. The signal takes on a flat-topped, or clipped
shape. When an amplifier tries to go above its max power, it clips.
compressor A signal processing device used to reduce the
dynamic range of the signal passing through it. For instance, an
input dynamic range of 110 dB might pass through a compressor and
exit with a new dynamic range of 70 dB. The modern usage for
compressors is to turn down (or reduce the dynamic range of) just
the loudest signals. Other applications use compressors to control the
creation of sound. When used in conjunction with microphones and
musical instrument pick-ups, compressors help determine the final
timbre by selectively compressing specific frequencies and wave-
forms.
connectors Audio equipment uses different styles:
RCA An unbalanced pin connector commonly used on
consumer and some pro equipment; aka phono plug
XLR A 3-pin connector common on pro audio equipment.
Preferred for balanced line interconnect; aka Cannon plug
¼" TRS 1. Stereo ¼" connector consisting of tip (T), ring (R),
and sleeve (S) sections, with T = left, R = right, and S =
ground/shield. 2. Balanced interconnect with the pos & neg
signal lines tied to T and R respectively and S acting only as an
overall shield. 3. Insert loop interconnect with T = send, R =
return, and S = ground/shield. [Think: ring, right, return]
¼" TS Mono ¼" connector consisting of tip (T) [signal] and
sleeve (S) [ground & shield] for unbalanced wiring.
constant-Q equalizer (also constant-bandwidth) The
bandwidth remains constant for all boost/cut levels. Since Q and
bandwidth are interrelated, the terms are fully interchangeable.
decibel Abbr. dB (named after Alexander Graham Bell). The
preferred method and term for representing the ratio of different
audio levels. Being a ratio, decibels have no units. Everything is
relative. So it must be relative to some 0 dB reference point. A suffix
letter is added to distinguish between reference points:
0 dBu A reference point equal to 0.775 V
+4 dBu Standard pro reference level equal to 1.23 V
0 dBV A reference point equal to 1.0 V
-10 dBV Standard reference level for consumer and some pro
audio use, equal to 0.316 V. RCA (phono) connectors are a
good indicator of units operating at -10 dBV
dynamic range The ratio of the loudest signal to the quietest
signal in a unit or system as expressed in decibels (dB).
expander A signal processing device used to increase the dynamic
range of the signal passing through it. Expanders complement
compressors. For example, a compressed input dynamic range of 70
dB might pass through a expander and exit with a new expanded
dynamic range of 110 dB. Modern expanders usually operate only
below a set threshold point, i.e., they operate only on low-level
audio. The term downward expander describes this type of applica-
tion.
ground Any electrical reference point for measuring voltage levels.
Usually a large conducting body, such as the earth or an electric
circuit connected to the earth. Chassis should always be at earth
potential.
WARNING: SHOCK HAZARD Never use an AC line cord ground-
lift adapter or cut off the 3rd pin. It is illegal and dangerous.
headroom The level in dB between the typical operating level and
clipping. For example, a nominal +4 dBu system that clips at +20
dBu has 16 dB of headroom.
hum Unwanted sound contaminating audio paths due to EMI
(electro-magnetic interference) caused by AC power-lines &
transformers getting into unbalanced, poorly shielded, or improperly
grounded connecting cables. Hum has a definite smooth (sine wave)
repetitive sound based on the harmonics of 50/60 Hz such as 100/
120 Hz and 150/180 Hz.
interpolating Term meaning to insert between two points. If a
graphic equalizer’s adjacent bands, when moved together, produce
a smooth response without a dip in the center, they are interpolat-
ing between the fixed center frequencies.
levels Terms used to describe relative audio signal levels:
mic-level Nominal signal coming directly from a microphone.
Very low, in the microvolts, and requires a preamp with at least 60
dB gain before using with any line-level equipment.
line-level Standard +4 dBu or -10 dBV audio levels.
instrument-level Nominal signal from musical instruments
using electrical pick-ups. Varies widely, from very low mic-levels
to quite large line-levels.
limiter A compressor with a fixed ratio of 10:1 or greater. The
dynamic action prevents the audio signal from becoming larger than
the threshold setting.
Linkwitz-Riley crossover The most preferred active crossover
design. It features steep 24 dB/octave slopes, in-phase outputs, and
flat amplitude response. Due to the in-phase outputs the acoustic
lobe resulting when both loudspeakers reproduce the crossover
frequency is always on-axis (not tilted up or down) and has no
peaking.
noise 1. Interconnect. Unwanted sounds contaminating audio paths.
RFI (radio frequency interference) caused by broadcast signals
leaking into unbalanced, poorly shielded, or improperly grounded
connecting cables. Also by light dimmers, motor controls and
computers. 2. Music. A random mix of audio frequencies not
harmonically related, sounding like radio static.
polarity A signal’s electromechanical potential with respect to a
reference. For example, a microphone has positive polarity if a
positive pressure on its diaphragm results in a positive output
voltage. polarity vs. phase shift: polarity refers to a signal’s
reference NOT to its phase shift. Being 180 degrees out-of-phase and
having inverse polarity are DIFFERENT things. We wrongly say
something is out-of-phase when we mean it is inverted. One occurs
over a period of time; the other occurs instantaneously.
Q (upper-case) Quality factor. Defined to be the ratio of the center
frequency f divided by the bandwidth BW for a bandpass filter.
signal-to-noise ratio The ratio in dB between a reference level
and the noise floor. For example, a signal-to-noise ratio of 90 dB re
+4 dBu, means the noise floor is 90 dB below a +4 dBu ref.
unbalanced line An audio interconnect scheme using one wire
with an overall shield. The shield must perform two functions: act as
the return signal path (ground) and to protect the conductor from
noise (shield). Consequently this method is vulnerable to hum &
noise problems.
unity gain A gain setting of one. The level out equals the level in.