Shock assembly filling the shocks with oil, Assembly of the spring, Assembly of the bevel gear – OFNA Racing MBX R2 Plus User Manual

Page 7

Advertising

#32237

O-Ring, rebuild

Shock Cylinder

( Make 2 for rear. )

( Make 2 for front.)

OIL

2. Pull down piston, attach pressure top
and shock oil overflow with tissue
paper.

SHOCK ASSEMBLY

FILLING THE SHOCKS WITH OIL

ASSEMBLY OF THE SPRING

1. Pull down piston and pour oil into
shock cylinder. Remove air bubbles
by slowly moving piston up and down.

3. Tighten up shock cap.

*Pull down.

*Move Slowly.

*Leave 3mm.

*Push Onto Shock
Cylinder

Shock Shaft

Piston

* Be careful not to damage shock shaft.

Pressure Top

#32044

Shock Cap, Hard Coated

Fit into groove.

#32203

Dust Pusher
(Yellow Rubber)

Oil Seal

* Fit into groove.

2mm
Washer

1mm
Washer

7mm
E-Ring

* E-Ring must
fit into groove as shown.

* Short shaft for front.

#32051

6mm Ball End,
Plastic parts bag

* Long shaft for rear.

2.6mm Nut

* Push 6mm ball joint
into ball end.

2.6 x 5mm
Washer

Spring Collar

Optional:

#32330

Red Spring set

#32340

Yellow Spring Set

Spring Holder

*Slide spring collar into Shock.

5mm

3mm

1mm

*Spring Tension adjust .

6mm
Ball Joint

#37380

* Screw down cap.

# 32033

* Assembly 4 pieces of the
shock Shaft .

#32291

Front, Short(w-gt) Shaft, 3.2mm

#32236

Rear, Long Shaft, 3.2mm

E-Ring

Hard Coated Shocks:
Front Super Shock, 3.5mm

# 32290

Rear Super Shock, 3.5mm

# 32230

#32051

6mm Ball End,
Plastic parts bag

Option:

#32039

O-ring Pistons

#32235

Teflon Piston Set

#32204

Spring Spacer Clips Set

#32051

All Plastic shock
parts bag

30121
3 x 5mm
Screw
(Small Head)

ASSEMBLY OF NEW “K” STYLE DIFFERENTIAL CASE AND GEARS

30751 Diff. Case ( Front/Rear )
30761 Diff. Case (Center )

30779
P5 O-Ring
( Orange )

30779
0.5 x 26mm
O-Ring

30779
2 x 12.8mm
Pin

30779
4 x 10mm
Washer

30769
Diff.
Bevel Gear
( Small )

30769
Diff. Bevel Gear
( Large )

30769
Diff.
Bevel Gear
( Large )

Grease

* Position the O-ring
as shown.

* Apply diff. Gear grease to the
differential, during assembly.

ASSEMBLY OF THE BEVEL GEAR

( Builds two differentials for front and rear. )

5 x 5mm
Set Screw

3 x 5mm
Screw

* Fill the diff. Case to
approx 70% with grease.

NB. It is very important to remove
the 30779 shim if the mesh
is too tight.

30773
4mm
Cross Pin

30771
Diff. Shaft

3x10mm
Tapping Screw

* Notice the straight holes
are for front and rear.

90026
5 x 5mm
Set Screw

39730
Cap Joint

36730
Cap Joint

30620
7 x 19mm
Bal lbearings

30620
7 x 19mm
Ball bearings

rew

31010
Optional - Bevel Gear

(Harden Steel)

30121
3mm
Tube

30121
3 x 5mm
Screw

* Push 3mm tubes into
holes of the diff. Case.

30120
Bevel Gear
(Large/Metal)

#31324 - FRONT OR REAR DIFF UNIT

#31325 - CENTER DIFF UNIT

Advertising

Popular Brands

Popular manuals