Testing the settings in the clone box, Testing the clone box battery, Probando la configuración en la caja de clonación – Panasonic CT-2010H User Manual
Page 12: Probando la pila de la caja de clonación
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
•
The red LED will flash while the data is
uploaded into the box. The green LED will
light for about two (2) seconds when the
procedure is complete.
•
If the green LED does not light for about two
(2) seconds, retry by holding the ALT button
while pressing the LEARN button.
7.
Disconnect the clone box from the
television and turn it OFF.
8. Reset the volume on the television.
9. Refer to the section entitled Setting Up
Other Televisions Using the Clone Box
(TEACH).
Testing the Settings in the Clone Box
This test compares the clone box settings with
the television settings. The television must be in
Commercial (Hotel) mode.
1. Press the POWER ON button on the clone
box.
•
The LEDs will flash red and green to confirm
power is ON.
2.
Connect the clone box to the Digital
Interface port on the back of the television.
•
The television must be plugged into an AC
outlet but can be either OFF or ON.
3. Press the TEST button.
•
The LEDs wilt flash red and green while the
data is compared. The green LED will light for
about two (2) seconds if the settings in the box
match the television.
4.
Disconnect the clone box from the
television and turn it OFF.
Testing the Clone Box Battery
1. Press the POWER ON button on the clone
box.
•
The LEDs will flash red and green to confirm
power is ON.
2. Hold the ALT button while pressing the
TEST
button.
•
The LEDs will alternately flash red and green
while the box is tested.
Note: Replace the 9 volt battery if the LEDs do
not flash red and green.
•
The green LED will light for about two (2)
seconds, if battery is charged.
Note: If the green LED does not light for about
two (2) seconds at the end of the test, new
data must be downloaded into the box.
•
EI indicador rojo emitirá una luz intermitente
mientras la información es grabada en la caja
de clonación. El indicador verde emitirá una
luz
continua
por
aproximadamente
dos
segundos cuando el procedimiento halla
concluido.
•
Si el indicador verde no emite luz por los
aproximados dos segundos, vuelva a intentar
presionando
el
botón
ALT
y
LEARN
simultáneamente.
7. Desconecte la caja de clonación del la
televisión y APAGUELA.
8. Reajuste el volumen en la televisión.
9.
Refiérase
a
la
sección
titulada
Configurando otras televispnes usando su
caja de clonación (ENSEÑA).
Probando la configuración en la caja
de clonación.
Mediante este procedimiento se compara la
configuración de la caja de clonación con la de la
televisión. La televisión debe estar en la
modalidad comercial (hotel).
1. Presione el botón POWER ON en la caja
de clonación.
•
Los indicadores rojo y verde emitirán una luz
intermitente para confirmar que la caja de
clonación está encendida.
2. Conecte la caja de clonación a la interface
digital en la parte posterior de la televisión.
•
Aunque la televisión puede estar encendida o
apagada debe estar conectada al suministro
de corriente alterna.
3. Presione el botón TEST (Prueba).
•
Los indicadores rojo y verde emitirán una luz
intermitente
mientras
se
compara
la
información. El indicador emitirá una luz verde
continua por aproximadamente dos segundos
si la configuración de la caja es igual a la de la
televisión.
4. Desconecte la caja de clonación de la
televisión y APAGUELA.
Probando la pila de la caja de clonación
1. Presione el botón POWER ON en la caja
de clonación.
•
Los indicadores rojo y verde emitirán una luz
intermitente para confirmar que la caja de
clonación está encendida.
2.
Mientras mantiene presionado el botón
ALT
oprima el botón TEST (Prueba).
•
Los indicadores rojo y verde emitirán una luz
alternada durante la revisión de la caja.
Nota:
Si el indicador no emite la luz verde y roja en
forma intermitente, reemplace la pila de 9
voltios.
-
12
-