Campbell Hausfeld NB006750 - Manual (Page 5)

5
NB006750
www.chpower.com
Operating The Nailer
(Continued)
ReCOMMeNDeD hOOKUP
The illustration below shows the
recommended hookup for the nailer.
1. The air
compressor
must be able
to maintain a
minimum of 70
psi when the nailer is being used.
An inadequate air supply can cause
a loss of power and inconsistent
driving.
2. An oiler can be used to
provide oil circulation
through the nailer. A
filter can be used to
remove liquid and solid
impurities which can rust or “gum
up” internal parts of the nailer.
3. Always use air supply
hoses with a minimum
working pressure rating
equal to or greater
than the pressure from
the power source if a regulator fails,
or 150 psi, whichever is greater. Use
3/8” air hose for runs up to 50’. Use
1/2” air hoses for 50’ run or longer.
For better performance, install a
3/8” quick plug (1/4” NPT threads)
with an inside diameter of .315”
(8mm) on the nailer and a 3/8” quick
coupler on the air hose.
4. Use a pressure regulator on the com-
pressor, with an operating pressure
of 0 - 125 psi. A pressure regulator
is required to control the operating
pressure of the nailer between 70
and 110 psi.
OPeRaTIONal MODe
Always know the
operational mode of
the nailer before using. Failure to know
the operational mode could result in
death or serious personal injury.
SINGle CYCle MODe
This mode
requires the
trigger to be
pulled each
time a nail is
driven. The nailer can be actuated by
depressing the WCE against the work
surface followed by pulling the trigger.
The trigger must be released to reset
the tool before another nail can be
driven.
WORK CONTaCT eleMeNT (WCe)
Check the operation
of the Work Contact
Element (WCE) trip mechanism before
each use. The WCE must move freely
without binding through its entire
travel distance. The WCE spring must
return the WCE to its fully extended
position after being depressed. Do
not operate the nailer if the WCE trip
mechanism is not operating properly.
Personal injury may occur.
1. Disconnect the air
supply from the nailer.
2. Remove all nails from
the magazine (see
Loading/ Unloading).
3. Make sure
the trigger
and work
contact
element
(WCE) move freely up and down
without sticking or binding.
4. Reconnect air supply to
the nailer.
5. Depress the Work
Contact Element
(WCE) against the
work surface without
pulling the trigger. The
nailer MUST NOT OPeRaTe. Do not
use the tool if it operates without
pulling the trigger. Personal injury
may result.
6. Remove the nailer from
the work surface. The
Work Contact Element
(WCE) must return to its
original down position.
The nailer MUST NOT OPeRaTe.
Do not use the tool if it operates
while lifted from the work surface.
Personal injury may result.
7. Pull the
trigger
and
depress
the work
contact element (WCE) against the
work surface. The nailer MUST NOT
OPeRaTe.
8. Depress
the Work
Contact
Element
(WCE)
against the work surface. Pull the
trigger. The nailer MUST OPeRaTe.
An improperly
functioning tool
must not be used. Do not actuate the
tool unless the tool is placed firmly
against the work piece.
lOaDING/UNlOaDING The NaIleR
1. Always disconnect the tool from
the air supply before loading
fasteners.
2. Press down
on the release
latch. Pull back
on the magazine
cover.
3. Insert a stick
of Campbell
Hausfeld nails
or equivalent
(see Fastener
Section) into the magazine. Make
sure the pointed ends of the nails
are resting on the bottom ledge
of the magazine when loading.
Make sure the nails are not dirty or
damaged.
4. Push the
magazine
cover forward
until the latch
catches.
5. Always unload all fasteners before
removing tool from service.
Unloading is the reverse of loading,
except always disconnect the air
hose before unloading.
70 psi
Min.
110 psi
Max.
150 psi WP
3/8 inch
I.D.
Movement
CAMPBELL PROFESSIONAL HAUSFELD
1 2
1 2
1 2