Yamaha RX-V1065 - Manual (Page 23)

Optimizing the speaker setting for your iistening room (YPAO)
4
When the speakers are connected to EXTRA
SP terminals, press HCursor A repeatedly
to select “Extra Speaker Assignment” and
then press HCursor <1 / o to select how to
use EXTRA SP terminals from “Zone2”,
“Presence” or “None”.
If this unit does not work when you press HCursor,
press [HON SCREEN once and then operate this
unit.
5
To select sound characteristics for
adjustment, press HCursor V to select “EQ
Type” and then press HCursor <!/[>.
If this unit does not work when you press HCursor,
press [HON SCREEN once and then operate this
unit.
This unit has a parametric equalizer that adjusts the
output levels for each frequency range. The equalizer
is adjusted to produce a cohesive sound field based on
automatically measured speaker characteristics.
In “EQ Type”, you can select the following
parametric equalizer characteristics suitable for the
desired sound characteristics.
Natural
This adjusts all speakers to achieve natural sound.
Select this if sounds in the high frequency range seem
too strong when “EQ Type” is set to “Elat”.
Flat
This adjusts each speaker to obtain the same
characteristics. Select this if your speakers have
similar qualities.
Front
This adjusts each speaker to obtain the same
characteristics as the front left and right speakers.
Select this if your front left and right speakers have
significantly better qualities than the other speakers.
6 Press HCursor V to select “Start” and then
press QIENTER to start the setup procedure.
A countdown starts and a measurement starts in 10
seconds. A loud test tone is output during
measurement.
Notes
• During ihc aulomatic setup procedure, do not perform any
operation on this unit.
• Press mCursor^ lo cancel the aulomatic setup procedure.
When measurement is successfully completed,
“YPAO Complete” appears on the front panel display
and the measurement result appears on the GUI
Measurement takes about 3 minutes. To obtain precise
results, stay where you will not disturb the
measurement, such as to the side of or behind the
speakers or outside the room.
Speaker Config ; 3/4/0.1
Distance (iin/Max) : 8.0ft/8.511
Level (Min/Max) ; -3.5dB/+4.
Speaker Config
Displays the number of speakers connected to this unit in
the following order:
Total of Front and Center/Total of Surround and Surround
Back/Subwoofer
Distance (Min / Max)
Displays the speaker distance from the listening position
in the following order:
Closest speaker distance/Farthest speaker distance
Level (Min / Max)
Displays the speaker output levels in the following order:
Lowest speaker output level/Highest speaker output level
Notes
* If “Error" appears on the GUI screen during “Auto .Setup", measurement
is canceled and the type of error is displayed. For details, see “When an
error message is displayed during measurement" (page 21).
• If problems occur during measuremcnl. “Check xx warning(s)" (xx
indicates ihc number of warnings) appears in red. For details, sec “When
a warning message is displayed after measurement" (page 21).
7
Press HENTER to confirm the settings.
The speaker characteristics are adjusted according to
measurement results.
To cancel the operation, press HCursor <1 /1> to
select “Cancel” and press HENTER.
When the following screen appears, remove the
optimizer microphone. “Auto Setup” is now
complete.
Please disconnect the micorphone
(Then this screen will automatically disappear)
The optimizer microphone is sensitive to heat. Store it
in a cool place and away from direct sunlight after
measurement. Do not leave it in a place where it will be
subjected to high temperatures such on an AV
component.
If you do not waul to apply ihc measurement results, select “Cancel".
Perform “Aulo SclLip" again if you change the number or positions of
speakers.
If you press OlENTER before removing the optimizer microphone.
“Auto Setup" of “Speaker Setup" in the Setup menu (page 55) is
displayed.
20 £n