How to use'jet-of-steam"feature, Howto use 'verticalsteam" feature, A caution – Panasonic NI-C55SR User Manual
Page 4: Awarning
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
"
" zone: Low steam, for thin or delicate fabrics requiring a small amount of steam.
"
" zone: High steam, for fabrics requiring a lot of steam (i. e. thick materials, items with
stubborn wrinkles).
5. Preheat the iron until the indicator light goes out, usually about 1 -2 minutes.
This light will go on and off during ironing to indicate the temperature chosen by the
Temperature Selector Dial is being maintained.
6. Hold the iron horizontally and move the Steam/Dry Selector into the steam position.
Steam/Dry Selector is regulated as follows.
NOTE:
3 Positions Steam/Dry Selector.
Dry
Low Steam Hiah Steam
(Right: for High Steam, Center: for Low Steam )
Temperature Zone
Steam/Dry Selector Position
O O
nr
Now steam ironing can begin
7. Whenever the iron is positioned vertically, the steaming action will stop.
A CAUTION
Do not use the Steam/Dry Selector at low or high steam positions until the Thermostat
Operating Indicator Light turns off after setting the Temperature Setting Dial within the
steam range. Otherwise hot water may leak from the Soleplate and burns may result.
HOW TO USE'JET-OF-STEAM"FEATURE
The"Jet-of-Steam"feature provides extra steam which goes deep into the garment and
is helpful for removing stubborn wrinkles. The"Jet-of-Steam" feature operates properly
only in the " <g$i " indication area of the Temperature Selector Dial when steam or dry
ironing( If used at lower setting, water spotting will occur because the iron is not hot
enough to change water to steam ). If you have not used the " Jet-of-Steam " feature
for a long time, it is necessary to clean the inside of the iron before using this feature
on any clothes to be ironed. Simply test the " Jet-of-Steam " feature several times
away from the ironing board and clothes to be ironed. This will prevent brown spotting
or water spotting on the clothes.
-7-
1. Fill the iron as described in " HOW TO FILL WITH WATER ".
2. Position the iron vertically and be sure the Temperature
Selector Dial is set to " OFF ".
Plug the AC Power Cord into the electrical outlet.
3. Set the Temperature Selector Dial to the " ^ " indication area
4. Preheat the iron until the indicator light goes out, usually
about 1 -2 minutes.
5. Simply pump the " Jet-of-Steam Button " when steam is
desired. Pump the " Jet-of-Steam Button " several times
at the beginning of each ironing session.
6. Allow at least 5 seconds between uses of "Jet-of-Steam
Button " to prevent water spotting. Use a press cloth if
necessary.
A CAUTION
Do not use "Jet-of-Steam Button " until the Thermostat Operating Indicator Light turns
off after setting the Temperature Setting Dial at 6.
Otherwise hot water may leak from the Soleplate and burns may result.
HOWTO USE 'VERTICALSTEAM" FEATURE
To get better results when using vertical steam, hang
the garment on a clothes hanger. Curtains and drapes
may also be steamed once they're hung. Hold the iron
away from your body, close to but not touching the fabric.
Pull the fabric tight with your free hand and pump the
Vertical Steam Button (Jet-of-Steam Button) at 5-second
intervals as you pass the iron over the wrinkled fabric.
AWARNING
Never iron clothes on the body or point your iron at anyone when steaming.
Keep hands and body away from steam areas while using vertical steam feature.
HOW TO USE THE SPRAY FEATURE
Before using the spray feature, check the fabric label for ironing instructions because some
fabrics may be spotted or stained with moisture.
The spray feature is particularly helpful for removing stubborn wrinkles and where extra
dampening is needed.
The spray may be used with steam or dry ironing.
-
8
-