Technical data, Initial settings, Putting the water heater into operation – STIEBEL ELTRON TEMPRA 12 B User Manual

Page 9: Normal maintenance

Advertising
background image

– 9 –

En

gl

is

h

10. Technical Data

Model

`BTVŨĜŝ

`BTVŨĜÑ

`BTVŨŝƃ

`BTVŨŝÔ

`BTVŨŝĎ

`BTVŨŗō

Mat. no.

ŝŝŗÔŝƃ

ŝŝŗÔŝĜ

ŝŝŗÔŝŝ

ŝŝŗÔŝÔ

ŝŗŝÄÄÑ

ŝŗŝÄÄō

Model

`BTVŨĜŝŨTùşń `BTVŨĜÑŨTùşń `BTVŨŝƃŨTùşń `BTVŨŝÔŨTùşń `BTVŨŝĎŨTùşń `BTVŨŗōŨTùşń

Mat. no.

ŝŝÔĜĎō

ŝŝÔĜĎŌ

ŝŝÔĜĎÄ

ŝŝÔĜĎĎ

ŝŝŗÔŝÑ

ŝŝŗÔŝō

Phase

1

1

1

1

1

1

Voltage

V

208

240

208

240

208

240

208

240

208

240

208

240

Wattage

kW

9

12

10.8

14.4

14.4

19.2

18

24

21.6

28.8

27

36

Max. amp, load

A

44

50

2 x 26

2 x 30

2 x 35

2 x 40

2 x 44

2 x 50

3 x 35

3 x 40

3 x 44

3 x 50

Min. required circuit

breaker size

A

60

60

2 x 40

2 x 40

2 x 50

2 x 50

2 x 60

2 x 60

3 x 50

3 x 50

3 x 60

3 x 60

Required wire size

AWG COPPER

6

6

2 x 8

2 x 8

2 x 8

2 x 8

2 x 6

2 x 6

3 x 8

3 x 8

3 x 6

3 x 6

Inlet temperature, max.

°F (°C)

131 (55)

Water flow to activate unit

t

GPM (

t

l/min) 0.37 (1.4)

0.50 (1.9)

0.50 (1.9)

0.50 (1.9)

0.77 (2.9)

0.77 (2.9)

Nominal water volume

GAL (l)

0.13 (0.5)

0.26 (1.0)

0.26 (1.0)

0.26 (1.0)

0.39 (1.5)

0.39 (1.5)

Working pressure, max.

PSI (bar)

145 (10)

Tested to pressure

PSI (bar)

290 (20)

Weight

lbs. (kg)

13.

5 (6.1)

1

6.1 (7.3)

1

6.1 (7.3)

1

6.1 (7.3)

1

9.0 (8.6)

1

9.0 (8.6)

Dimensions

height

depth

width

inch (mm)

14 1/2 (369)

4 5/8 (117)

16 5/8 (420)

Water connections

NPT

3/4"

– Tankless water heaters are considered a non-continuous load – Conductors should be sized to maintain a voltage drop of less than 3 % under load

7. Initial

settings

Check whether the set value transducer cable is plugged into the
slot

T

Soll

A1 (TEMPRA B) or T

Soll

D (TEMPRA Plus) on the main PCB.

F

1

Selection of °F or °C units

- Set jumper on the dial-printed circuit board to °F or °C.

-

F

2

Activate anti-scalding protection function

On the TEMPRA Plus, an anti-scalding protection function can be
activated by two different methods.
1. Limit the outlet temperature to the fixed temperature of 109 °F

(43 °C).

- Insert the coding plug into position Tred (reduced temperature).

2. Select a specific outlet temperature

- Switch the appliance 'live'.

- Open the casing so that coding plug

T

max

/

T

red

becomes accessible.

- Set the temperature selector to "OFF". The coding plug must be

set to

T

max

(standard delivery).

- Set coding plug to

T

red

; the setting mode will be activated and

the flashing display shows the current temperature limit.

- Within the next 30 seconds, you can select the required

temperature (display continues to flash). The setting mode will
terminate after 30 seconds; the programming unit will display
"OFF" again.

8. Putting the water heater into

operation

!

WARNING: OPEN HOT WATER FAUCET FOR A FEW
MINUTES UNTIL WATER FLOW IS CONTINUOUS AND ALL
AIR IS PURGED FROM WATER PIPES. THE UNIT’S COVER
MUST BE INSTALLED BEFORE THE CIRCUIT BREAKERS ARE
TURNED ON.

1. Close the cover and fix it using the screw with chopper disc.

2. Turn on circuit breakers to bring electrical power to the unit.

3. Turn the temperature selector clockwise and anti-clockwise, to

calibrate the set value transducer.

4. Adjust the water temperature to the desired level using the knob

on the front cover of the unit.

5. Turn on hot water and wait twenty seconds until temperature

has stabilized.

6. Check the water temperature with your hand and make sure

that it does not feel too hot. Reduce if necessary.

7. Explain to the user how the unit works and familiarise him

or her with its use.

Advise the user about possible hazards (hot water temperature
up to 140 °F / 60 °C). Hand over these instructions, to be kept
for future reference.

9. Normal

maintenance

!

NOTICE: THE TEMPRAS DO NOT CONTAIN ANY PARTS
SERVICEABLE BY THE LAY PERSON. IN CASE OF
MALFUNCTION PLEASE CONTACT A LICENSED PLUMBER
OR ELECTRICIAN.

STIEBEL ELTRON TEMPRA tankless water heaters are designed
for a very long service life. Actual life expectancy will vary with
water quality and use. The unit itself does not require any regular
maintenance. However, to ensure consistent water flow, it is
recommended to periodically remove scale and dirt that may build
up at the aerator of the faucet(s), the filter screen in the unit, or
in the shower head.

Advertising