AvaLAN Wireless AW2400mSPI-10 - Manual (Page 14)

AW2400mSPI User’s Manual
PAGE 14 Technical support (650) 384-0000 www.avalanwireless.com
Status Command
The getStatus command is used to find out the current status of the module.
getStatus SPI Mode: 0x01 UART Mode: 0x00
Byte 1 b7 b6 b5 b4 b3 b2 b1 b0
RFState Radio - CH4 CH3 CH2 CH1 CH0
RFState: When set this bit indicates that the RF is currently connected.
Radio: Indicates what mode the radio is in, when set it is in active mode. When
clear the RF is in standby mode.
CH4..0: Indicates what channel the RF is currently using.
The setStatus command is used to place the module in standby mode/normal op-
eration and to set the RF into manual channel mode by assigning a specific channel.
setStatus SPI Mode: 0x81 UART Mode: 0x80
Byte 1 b7 b6 b5 b4 b3 b2 b1 b0
- Radio - CH4 CH3 CH2 CH1 CH0
Radio: Setting this bit places the radio in active mode, clearing it places it in
standby mode.
CH4..0: When these bits are cleared the radio is in automatic channel mode. When
any of these bits are set the radio will be in manual channel mode and using the
channel indicated by these bits if it is valid.
Chan CH4 CH3 CH2 CH1 CH0 Freq - GHz Chan CH4 CH3 CH2 CH1 CH0 Freq - GHz
1 0 0 0 0 1 2.416667 GHz 16 1 0 0 0 0 2.447917 GHz
2 0 0 0 1 0 2.418750 GHz 17 1 0 0 0 1 2.450000 GHz
3 0 0 0 1 1 2.420833 GHz 18 1 0 0 1 0 2.452083 GHz
4 0 0 1 0 0 2.422917 GHz 19 1 0 0 1 1 2.454167 GHz
5 0 0 1 0 1 2.425000 GHz 20 1 0 1 0 0 2.456250 GHz
6 0 0 1 1 0 2.427083 GHz 21 1 0 1 0 1 2.458333 GHz
7 0 0 1 1 1 2.429167 GHz 22 1 0 1 1 0 2.460417 GHz
8 0 1 0 0 0 2.431250 GHz 23 1 0 1 1 1 2.462500 GHz
9 0 1 0 0 1 2.433333 GHz 24 1 1 0 0 0 2.464583 GHz
10 0 1 0 1 0 2.435417 GHz 25 1 1 0 0 1 2.466667 GHz
11 0 1 0 1 1 2.437500 GHz 26 1 1 0 1 0 2.468750 GHz
12 0 1 1 0 0 2.439583 GHz 27 1 1 0 1 1 2.470833 GHz
13 0 1 1 0 1 2.441667 GHz 28 1 1 1 0 0 2.472917 GHz
14 0 1 1 1 0 2.443750 GHz 29 1 1 1 0 1 2.475000 GHz
15 0 1 1 1 1 2.445833 GHz