California Faucets Widespread Lavatory Faucet - Manual (Page 2)

"A"
Sink/
Countertop
Escutcheon
Spacer
Cup
Fiber
Washer
Bottom
Nut
Flex
Line
Valve
Lift Knob
Hole Rod
Strap
Nut
Ball
Rod
Cone
Washers
Fiber
Washers
Drain
Tailpiece
Rubber
Washer
Drain
Collar
Stopper
Drain
Rim
Adjustable
Eye-Screw
Nut
Brass
Nut
Connect faucet to water supply (See Fig. 6) :
IMPORTANT: Flush supply lines of all debris prior to connecting to lavatory
valve bodies. Debris remaining in the line will damage valve bodies and
cause leaking. Failure to flush the lines could result in voiding the warranty.
5
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Adjustable
Eye-Screw
Ball
Rod
Lift
Rod
Drain
Tailpiece
"P" Trap
(not supplied)
Angle Stop
(not supplied)
Valve
Body
Supply Riser
(not supplied)
2
Spring
Clip
Lock
Nut
-Connect supply risers from the angle stops.
NOTE:
P-trap, angle stops, and supply risers
are not supplied. We recommend genuine
Cal-Trim parts available at your authorized
California Faucets dealer.
P2
4
3
Install pop-up assembly (See Fig 4 & 5) :
7102-INSTL_081120
NOTE: Hot & cold valves are labeled: RED = hot & BLUE = cold.
-Remove top nut and discard.
-Turn bottom nut with fiber washer down the valve until it stops.
-Place spacer cup onto valve oriented correctly as shown.
-Insert valve through hole from below.
-Attach and thread escutcheon onto threads below stem and
adjust valve to scheduled height "A".
-Place handle onto stem allowing minimal gap between escutcheon and
handle. Tighten setscrews with Allen key provided.
-Align handle in desired position and tighten the bottom nut to secure valve.
NOTE: Align square escutcheon on 7202 Series prior to securing valve.
-Attach flex lines between valves and spout tee.
-Flex lines shall be handtightened, then tighten 1/4 to 1/2 turn with wrench.
(wrench not supplied).
-Separate drain collar from pop-up assembly.
-Apply silicon caulking to underside of drain collar. NOTE: Do not use
"Plumbers Putty" or any oil based sealants! Use of anything other than
silicon caulking will VOID the finish warranty.
-Insert drain body from underside through sink. Slowly screw on drain
collar, align with ball rod hole facing back wall, then gently pull down into
sink and firmly tighten brass nut from below.
-Remove tailpiece from drain body and apply teflon tape, approx. 3 to
5 wraps around threads and reinstall into bottom of drain body.
-Insert stopper in collar and hold with eye-screw hole facing back.
If necessary, adjust stopper eye-screw height by loosening lock nut and
rotating counter-clockwise. Tighten lock nut (See Fig. 4).
-Remove spring clip from ball rod.
-Remove nut and cone washers and slide onto end of ball rod.
-Insert ball rod into drain body below so short end of ball rod end fits
in stopper eye-screw hole. Snug ball rod nut (do not over tighten).
Ball rod must move up & down freely (See Fig. 4).
-Insert lift rod through top of spout and then through hole rod strap
underneath sink. Tighten thumb-screw of hole rod strap
against lift rod and connect to ball rod by gently pinching locking
spring clip and sliding one side of spring clip onto ball rod.
-Insert hole strap onto ball rod, then pinch spring clip together to fit
on ball rod.
Fig. 3
7102 Series
"A" = 1"
7202 Series
"A" = 3/4"
7302 Series
"A" = 1"
Install "P" trap (See Fig. 7) :
-Connect your waste "P" trap
to the drain tailpiece.
6 Turn on Water Supply:
Operate hot and cold valves: Inspect all joints and fittings for leaks.
NOTE: Due to sediment in the water it may be necessary on occasion to remove the aerator/flow restrictor and clean the
screen with a soft bristle toothbrush.
IMPORTANT CLEANING NOTICE: Please refer to Finish Care Instructions for complete cleaning information. Wipe frequently
with a soft, damp cloth. Never use acids, harsh abrasives or detergents.
Install valve bodies (See Fig. 1 & 3) :