Inovonics EN1260 - Manual (Page 2)

© Inovonics, 2011 - www.inovonics.com 2
3 Test the EN1260
3.1 Perform a Walk Test
The walk test is performed to test the PIR, ensuring motion is sensed. To perform a
walk test:
1.
Hold the magnet to the reed switch for less than one quarter of a second, The
LED will light three times to indicate the three-minute walk test has been
activated.
Note: To activate the walk test, the magnet shouldn’t remain near the reed switch for
more than one-quarter of a second.
2. Walk in front of the PIR to test the sensor. The LED will light every time the PIR
senses motion.
3. The unit will not transmit alarm signals during the three minute test period. When
the walk test ends, the LED will light six times.
3.2 Perform Transmission Test
1. Hold the magnet to the reed switch for more than four seconds. The LED will light
three times to indicate the transmission test has been activated.
2. The unit will transmit alarm and restoral cycles at regular intervals for
approximately one minute. The LED will light every time the unit transmits. Ensure
transmissions are received by your network coordinator, receiver or control panel.
4 Operation
The EN1260 transmitter signals an alarm condition when motion is detected by the
sensor.
4.1 Zone Pattern for Standard Lens
The standard wide-angle lens has a coverage pattern of 105°, and covers an area 18
m x 18 m (60 ft x 60 ft). It has a total of 52 zones: (18 long range + 16 intermediate +
ten short range + six nearest range + two creep zones). Optional lenses are available.
Contact Inovonics Wireless technical services.
4.2 Lens Options
The following optional lenses are available for the EN1260:
• ACC672CT curtain lens
• ACC672LR long range lens
• ACC672PA pet alley lens
Note: Mounting height of the EN1260 with standard lens may be anywhere within a
range of 7 to 9 feet (2.1 to 2.7 m).
Figure 3 EN1260 zone map
5 Specifications
Dimensions: 4.5”H x 2.5”Wx 1.6”D (11.4 8cm x 6.4 cm x 4.1 cm)
Operating temperature: -4° to 140°F (-20° to 60°C)
Humidity: 0 - 90% (non-condensing)
Battery: 3V lithium (CR123A orDL123A)
Tamper: Housing and wall tamper
PIR RF interference immunity: Greater than 30 v/m 26 MHz - 1 GHz
Alarm lockout time: 3 minutes
Mounting height: 7 to 9 feet (2.1 to 2.7 m)
6 Television and Radio Interference
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
7 FCC Part 15 and Industry Canada Compliance
This device complies with part 15 of the FCC Rules and Industry Canada license-
exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
8 Warranty and Disclaimer
Note: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Inovonics Wireless Corporation ("Inovonics") warrants its EchoStream products
("Product" or "Products") to conform to its own specifications and to be free of defects
in materials and workmanship under normal use for a period of thirty-six (36) months
from the date of manufacture. Within the warranty period, Inovonics will repair or
replace, at its option, all or any part of the warranted Product. Inovonics will not be
responsible for dismantling and/or reinstallation charges. To exercise the warranty, the
User ("User", "Installer" or "Consumer") must work directly through their authorized
distributor who will be given a Return Material Authorization ("RMA") number by
Inovonics. Details of shipment will be arranged directly through the authorized
distributor.
This warranty is void in cases of improper installation, misuse, failure to follow
installation and operating instructions, alteration, accident or tampering, and repair by
anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other warranties, obligations or
liabilities, whether written, oral, express, or implied. There is no warranty by Inovonics
that Inovonics product will be merchantable or fit for any particular purpose, nor is
there any other warranty, expressed or implied, except as such is expressly set forth
herein. In no event shall Inovonics be liable for an incidental, consequential, indirect,
special, or exemplary damages, including but not limited to loss of profit, revenue, or
contract, loss of use, cost of down time, or interruption of business, nor any claim
made by distributor's customers or any other person or entity.
This warranty will not be modified or extended. Inovonics does not authorize any
person to act on its behalf to modify or extend this warranty.
This warranty will apply only to Inovonics Products. Inovonics will not be liable for any
direct, incidental, or consequential damage or loss whatsoever, caused by the
malfunction of Product due to products, accessories, or attachments of other
manufacturers, including batteries, used in conjunction with Inovonics Products.
Top
View
Side
View